In short

A pre-shipment inspection is a sample-based check of finished goods before they leave the factory, normally covering quantity, specification, workmanship, dimensions, packing and marks, and judged against an agreed sampling plan rather than an inspector's opinion. The output is a report with measurements, numbered photographs and a defect list.

It is routinely confused with two other checks. A factory audit looks at the site and the system. A laboratory test looks at a material against a named standard. Neither tells you whether the 240 chairs leaving on Friday match the drawing signed in June. Only an inspection does, and only if the drawing, the sample and the sampling plan were agreed first.

01The inspection checks goods, not the factory

Three checks are sold in one conversation and answer different questions. An audit establishes which legal entity makes the goods and how much it can produce. A pre-shipment inspection establishes whether the goods on the floor match the purchase order. A laboratory test establishes whether a material meets a named standard. A quotation that answers one and implies another is a common misunderstanding.

Timing matters as much as scope. An inspection during production catches a fault while the line can still change a setting. An inspection at the end catches it when the remedies are rework, a discount or a rejection. Loading supervision is narrower still: it confirms what went into the container, not what was made.

Decision rule: name the check in the purchase order — audit, during-production inspection, pre-shipment inspection, loading supervision or laboratory test — and attach the report each one produces. A line saying 'inspection arranged' buys none of them.

02Six categories, six kinds of evidence

A scope survives a dispute when it is written as checkable statements. 'Good quality' is not checkable. 'Carton count equals 240, mark reads PO line 4, cabinet width 600 mm ±1 mm' is checkable, and the inspector either confirms it or does not.

The six categories a pre-shipment inspection covers, how each is verified, and the record it should leave.
Category How it is checked Coverage Record
QuantityCount cartons and units against the packing list100% of cartonsSigned count sheet
SpecificationCompare material, finish and hardware with the approved sampleSampleGoods photographed beside the sample
WorkmanshipCheck joints, glue squeeze-out, gaps, scratches, hardware alignmentSampleNumbered defect photographs
DimensionsMeasure against the drawing with tape, calliper or squareSampleValues with units, not pass or fail
PackingOpen cartons; check board grade, foam, corners, inner fitSeveral cartonsPacking photo set
MarksMatch carton marks to the packing list and shipping marks100% of cartonsMark photograph and carton map

Coverage is decided by the sampling plan, not by the inspector's judgement. Confirm the plan before the visit.

What the eye cannot do matters as much. An inspector can see that a panel edge is banded. He cannot see whether the adhesive is the specified grade, whether the board meets its declared class, or whether the coating will still adhere after a year outdoors. Composition and hidden performance belong to a laboratory, with the method and the sample named in the report.

Decision rule: attach the signed drawing and a physical approved sample to the inspection brief. An inspector comparing goods against a catalogue photograph is measuring nothing.

Catalogue reference: inspection coordination inside the sourcing service — models, dimensions and finishes for the directions discussed above.

03AQL turns a look into an accept or reject

Acceptance sampling under ISO 2859-1 fixes the sample size from the lot size and inspection level, then the acceptance number from the AQL. The AQL is not a target defect rate; it is the rule that decides whether the lot is accepted.

For general inspection level II at AQL 2.5 on major defects, the plan is fixed. A lot of 1,201–3,200 pieces is code letter K, the sample is 125 pieces, and the lot is accepted at 7 major defects and rejected at 8. Read the same table at a tighter AQL and the accept number falls.

ISO 2859-1 single sampling plans, general inspection level II, AQL 2.5 for major defects. Lot and sample sizes in pieces.
Lot size Code Sample Accept Reject
501–1,200J8056
1,201–3,200K12578
3,201–10,000L2001011

Values from ISO 2859-1 Tables 1 and 2-A. State the standard edition and the level in the order.

Classify defects before the inspector arrives. A common structure is critical at AQL 0, so any occurrence rejects the lot, major at 2.5 and minor at 4.0. A critical defect makes the product unsafe or unusable; a major one would stop a sale; a minor one is a finish mark a buyer might accept at a discount. The classes decide the disposition, so they belong in the purchase order.

The sample is drawn at random across cartons, not from the top of the first pallet. An inspector who takes the first 125 units off the line is describing the line's strongest hour.

04Access is a clause, not a favour

An inspection depends on three permissions: the inspector is allowed on site, the goods are complete and packed when he arrives, and nothing leaves the factory before the report is issued. Each is easy to grant in an email and easy to lose in a schedule.

Pre-shipment work requires the lot to be 100% produced and packed. Inspecting half a lot produces a report about half a lot. Where production runs across two sites, or where upholstery, glass or stone tops come from a subcontractor, the inspection covers both or states what it excludes.

The report also needs authority. If the supplier appoints and pays the inspector, the buyer is reading a supplier document with photographs. That is a progress record, not independent evidence, and it should not be the only condition on a balance.

Decision rule: the purchase order names the inspector, the address, the notice period and the person who grants access. An inspection arranged by email after production is a request, not a right.

05Packing and marks fail after the product passes

Packing is inspected because it is the part of the order that travels. A cabinet that passes on the bench and arrives with a crushed corner failed at the carton, which was the cheaper thing to specify.

The check is physical. Open cartons from the middle of the stack. Look at board grade, corner protection, foam at the edges, the fit of the inner packing and whether the hardware box can move. 'Export carton' is not a specification; the grade, the ply, the foam thickness and the corner blocks are.

Marks carry destination, item number, carton count such as 3 of 6, gross weight and the PO line. A wrong mark stops the warehouse receiving the goods, and nobody at the destination can reprint it. In a consolidated container every carton must map to a supplier and an item on the packing list, or a shortage cannot be traced.

Solid-wood crates and pallets are a separate regulated item from the product inside. Ask which packing is solid wood and confirm the mark before the crates are built.

Decision rule: the packing specification and the carton mark format go into the order as a drawing, and the packing list maps every carton to a supplier and an item.

06The report is evidence, or it is a story

A useful report contains measured values with units, a numbered photograph for each defect, a count by defect class and a disposition for each class. 'Minor scratches noted' cannot be priced or argued with. 'Three units, left door edge, 40 mm scratch, major class' can be both.

Two items make the report usable after the inspector leaves: the raw photo set and the retained sample. Number each photograph and tie it to the carton and the unit, so a replacement can be discussed without reopening the container. The sample stays with the supplier until the balance is settled.

The disposition is a commercial decision, not an inspection one. Accept the lot, accept with a price reduction, rework and re-inspect, or reject. Write those four options and the person who chooses between them into the order. Otherwise the report arrives, everyone agrees it is fair, and the goods ship because the vessel is booked.

The payment structure decides what the report is worth. On 30% deposit and 70% before shipment by T/T, the balance falls due before anything can be checked at the destination. That makes the report the last point of leverage; one issued after the container is sealed describes goods nobody can inspect again.

Decision rule: no accepted report, no balance. Release the 70% against a report that lists measurement values and defect counts, not against a summary sentence.

07Write the inspection into the purchase order

The sequence is short, and every step leaves a document that the next step depends on.

  1. Agree the specification, drawing and physical sample before the deposit, and record the approval date.
  2. State the inspection standard, level, AQL and defect classes on the proforma invoice.
  3. Name the inspector, the address, the notice period and the person who grants access.
  4. Book the inspection when production is complete and packed, and send the packing list ahead.
  5. Read the report against the specification and the sample, not the summary line.
  6. Release the balance against the accepted report and file the photo set with the shipping documents.

Incoterms 2020 sits alongside this and does not replace it. The rule, with its named place, decides where cost and risk transfer: 11 rules, seven for any mode and four for sea and inland waterway. A clean report does not move that point; it reduces the chance of paying for defective goods before they travel.

Decision rule: if the report, the packing list and the carton marks do not agree, the goods are not ready, whatever the schedule says.

What your RFQ should state

  1. The inspection standard and level: ISO 2859-1, general inspection level II, with the lot size in the unit sampled.
  2. The AQL for critical, major and minor defects, with each class defined line by line.
  3. The specification documents the inspector measures against, listed by revision and date, plus the physical approved sample on site.
  4. The address where packed goods will be presented, the notice period in working days and the named person who grants access.
  5. The report contents: measured values with units, numbered photographs, a defect count by class and a disposition for each class.
  6. The rule that no goods leave the factory and no balance is released until the report is accepted.
  7. Who pays for a re-inspection if the first fails, and the deadline for completing rework.
  8. The packing specification and carton mark format, with every carton mapped to a supplier and an item.

Where this guidance stops

Questions buyers ask

What does a pre-shipment inspection cover?

Quantity, specification against the approved sample, workmanship, dimensions against the drawing, packing and carton marks. The inspector samples the lot under an agreed plan, usually ISO 2859-1, and reports measured values, numbered photographs and a defect count by class. It does not cover material composition, hidden performance or the factory's capacity.

What is AQL and which level should I use?

The acceptable quality limit is the defect rate that the sampling plan will accept most of the time. General inspection level II with AQL 2.5 for major defects and 4.0 for minor ones is a common starting point for furniture and building materials. A tighter AQL means a larger sample or a smaller accept number, and more lots rejected.

Can an inspection confirm material or fire performance?

No. An inspector can read a label and check that a document exists; he cannot confirm resin content, formaldehyde class, fabric fire behaviour or coating adhesion by looking. Those need a laboratory working to a named method, ideally under ISO/IEC 17025 accreditation, with the sample identified in the report.

Who books and pays for the inspection?

It is a commercial term, so write it into the purchase order. Either the buyer appoints an independent inspector and the supplier grants access, or the supplier arranges a check and the buyer accepts a supplier document. The second is cheaper and weaker: it is not independent evidence, and it should not be the only condition on a balance payment.

What happens if the inspection fails?

The lot is not released. The order should already say what follows: rework to the drawing, a re-inspection at an agreed cost, a price reduction, or rejection and replacement. Without those options written down, a failed report becomes a negotiation conducted while a vessel is waiting, and the schedule usually wins.

Is a pre-shipment inspection the same as a factory audit?

No. An audit examines the site, the legal entity and the production system, usually before or during an order. A pre-shipment inspection examines the finished goods at the end. An audit can tell you whether a factory is capable; only an inspection tells you whether this lot was made to your specification.

Should the inspection happen before or after packing?

After packing, for a pre-shipment check. Packing and marks are part of the scope, and the lot should be complete, so the sample represents everything that will ship. A during-production check is the earlier option when a fault would be expensive to fix once the goods are boxed, and the two can be used together.

Sources

  1. ISO 2859-1 — Sampling procedures for inspection by attributes — International Organization for Standardization
  2. Incoterms 2020 rules — International Chamber of Commerce
  3. National Enterprise Credit Information Publicity System — State Administration for Market Regulation, China
  4. Importing into the United States — basics for importers — US Customs and Border Protection
  5. ISO/IEC 17025:2017 — General requirements for the competence of testing and calibration laboratories — International Organization for Standardization
  6. ISO 9001:2015 — Quality management systems: requirements — International Organization for Standardization
  7. IAF CertSearch — register of accredited management system certificates — International Accreditation Forum

Pages related to this guide

How this guide was checked

FS

Foshan Supply editorial team · Catalogue indexMethodology

Written in Foshan and reviewed against the catalogue and public standards on 2026-11-05. This page is a buying guide, not a quotation or a warranty. How we work.

How to cite this page: Foshan Supply, “Pre-shipment inspection: scope, sample and report”, 2026-11-05, https://foshansupply.com/blog/pre-shipment-inspection/