In short
- A fluted wall panel is a milled or extruded profile in MDF, solid timber, aluminium or PET. The material decides moisture, fire class and fixing.
- MDF machines a crisp profile and absorbs water at every unsealed cut edge. In a wet room, the board grade and the sealed edge matter more than the face.
- Fire class and acoustic ratings describe a tested assembly, not a board. The report has to name the substrate, the adhesive, the cavity and the joint.
A fluted wall panel is a rigid board or extrusion milled with repeated grooves and sold as a decorative wall lining, in MDF, solid timber, aluminium or PET. The buyer chooses the profile; the board behind it is what the wall has to live with.
Those four materials do not behave alike. They swell, move, char and dent differently, and each one asks for a different fixing. The showroom presents them as one object in four finishes. The decisions that follow are then made by whoever installs them, which is why moisture, fire class and access are the things that go wrong after handover.
01Four materials behave like four different products
The material decides moisture behaviour, fire route and fixing, so it belongs in the specification rather than the finish schedule.
MDF is a dry-process fibreboard: dense and easy to machine, which is why it holds a sharp groove. The uniformity is also the weakness. A cut edge is open fibre, and the edge, not the face, meets water at a floor line.
Solid timber moves across the grain as humidity changes, so a long run needs a movement gap rather than a tight butt. Aluminium is an extrusion: stable, usable outside with a coating, but usually a hollow section needing a frame. PET is extruded polymer, often slats on a felt backing, stable in humid rooms but dependent on the backing and adhesive.
| Material | Moisture | Fire route | Fixing | Where it fails |
|---|---|---|---|---|
| MDF | Swells at an unsealed cut edge; needs a humid grade | Depends on board and treatment; test the faced board | Screws or clips into battens | Cut edges at a floor line |
| Solid timber | Moves across the grain; needs a movement gap | Depends on species and section | Secret fix through a tongue | A tight joint that opens |
| Aluminium | Stable; usable outside when coated | Section is non-combustible; coatings count | Extruded frame or clip | Dents and a hollow note |
| PET | Stable; the felt backing is not | The backing governs the class | Adhesive or clips | Slat-to-backing bond |
Confirm the declared grade and class for the exact board. A class for a raw board does not cover a faced or bonded panel.
The rule is the room, not the photograph. A shower wall, a splashback behind a hob and a hotel corridor are three specifications.
02Moisture picks the material before the budget does
Water reaches a fluted panel at the cut edge, so the number that matters is the length of open edge on the order, not the area of the face.
A 2,400 × 1,200 mm panel has 7.2 m of cut perimeter. At 12 mm thick that perimeter exposes 0.086 m² of raw fibre; at 18 mm it is 0.13 m². A film face seals none of it.
EN 622-5 sorts dry-process fibreboard by the conditions it is made for, so the grade tells you what the board is for. A film-faced MDF panel with an unsealed bottom edge behind a skirting is a dry board in a wet room.
The remedy is procedural: declare the humid grade, seal the cut edges and the back face, and keep the bottom edge out of standing water. Ask which sealant, how many coats, and whether the factory or the installer seals.
In a shower, above a bath or in an unheated room, MDF is out unless the board is declared for humid conditions and every cut edge is sealed. Otherwise specify aluminium or PET.
Catalogue reference: fluted and linear wall panels in the catalogue — models, dimensions and finishes for the directions discussed above.
03Fire class belongs to the lining, not to the board
A fire class is the result of a reaction-to-fire test, reported under EN 13501-1 as a main class from A1 to F with smoke and droplet sub-classes. It describes what was tested, not the wall it ends up on.
Two certificates get confused here. Reaction to fire asks how a lining feeds a fire growing in a room. Fire resistance, tested for a door set to EN 1634-1, asks how long an assembly holds a fire back.
A board tested bare in a rig is not the panel bonded to plasterboard with a combustible adhesive over a ventilated cavity. The adhesive, the cavity and the substrate sit inside the tested assembly; a report naming only the board answers a question nobody asked.
| The report must name | Why it changes the result | What to ask for |
|---|---|---|
| Board and face | A film or paint changes the class of the same core | The page naming product and thickness |
| Adhesive | A combustible adhesive is fuel in the assembly | Adhesive and coverage used in the test |
| Substrate | Plasterboard, concrete and timber differ | The substrate tested, and the one on site |
| Cavity and battens | A ventilated cavity behaves differently | Cavity depth and batten material |
| Joints and seals | A gap or a sealant changes spread at the joint | The joint drawn, not described |
A class letter on a data sheet is a claim until the report names the assembly. Ask for the page, not the summary.
Where the wall is a means of escape, the class is a code decision made by whoever signs the fire strategy. The supplier's job is to prove the assembly.
04A hidden fixing is a decision about access
A hidden fixing buys a clean face and sells the right to remove a panel, a trade worth pricing before the order rather than after the first leak.
Most systems hide the screw behind the groove: a clip, a cleat or adhesive on battens. The face reads as one surface and the installer has no way back. When a pipe fails, a bonded panel is cut out; a clipped one lifts off.
Weight sets the fixing schedule. At a declared density of 750 kg/m³, a figure to confirm rather than assume, a 12 mm board is 9.0 kg/m². One 2,400 × 1,200 mm panel at 2.88 m² weighs about 26 kg, and a 4,800 mm run carries five at roughly 130 kg.
Ask for the load per clip and the spacing the manufacturer requires. A clip loaded to its declared limit with no margin lets go the first time a door in the same wall slams.
Any wall containing services gets a removable panel or an access hatch, agreed in writing before the order. A wall with no services can be bonded.
05Flatness is the trade nobody quotes
A rigid panel follows the wall behind it, so the wall is part of the product and the tolerance is part of the price.
For a roll covering, the wall has to be flat and primed. A rigid panel is stricter in one way and looser in another: it cannot stretch over a hollow, but it can be packed out on battens. The pack-out is the trade nobody has quoted.
Check with a 2 m straightedge and record the worst deviation in millimetres, room by room, before the battens go on. A glued panel absorbs none of it; a clipped panel absorbs only what the clip slot allows.
As a planning reference, battens at 400 mm centres suit a 12 mm MDF panel and 600 mm an 18 mm board; confirm both against the clip supplier's span table. On a 4,800 mm wall at 400 mm centres that is 13 vertical battens and 9.6 m of rail.
A batten line that is not straight shows as a shadow inside the groove, because a groove is a straight edge held against a wavy wall. Put the deviation, the spacing and the pack-out allowance in the RFQ.
06Panel count, joints and the waste you pay for
Set the panel height against the wall height before counting panels, because the strip left at the ceiling is an order line that the area calculation hides.
A 4,800 × 2,700 mm wall is 12.96 m². A 2,400 × 1,200 mm panel is 2.88 m², so the area needs five panels at 14.4 m², 11% more than the wall. Run vertically, each covers 1,200 mm of width and 2,400 mm of the height, leaving a 300 mm band at the ceiling.
| Item | Value | Note |
|---|---|---|
| Wall area | 12.96 m² | 4,800 × 2,700 mm |
| Panel area | 2.88 m² | 2,400 × 1,200 mm |
| Panels at full height | 5 | 14.4 m², 11% over |
| Ceiling band | 300 mm | Vertical panels at 2,400 mm |
| Panel mass at 12 mm | 25.9 kg | At 750 kg/m³, to confirm |
| Battens at 400 mm | 13 | Plus 9.6 m of rail |
Substitute your own dimensions and confirm the density and panel size with the supplier before ordering.
Joints are the other order line. A 3 mm shadow gap reads as a drawn line; the same 3 mm unsealed is a route for water and air, and at a door reveal it is where the certificate argument starts.
Order the batch in one go. A second order placed later will not match on colour or profile depth, and the mismatch sits at eye level.
07A panel on a door face joins the door set
A fluted panel that runs from a wall onto a door face stops being a lining and joins a tested set. A fire door is certified as a set: leaf, frame, seals, hinges and hardware, under EN 1634-1, and the leaf alone is not the rating. Bond a 12 mm panel to a certified leaf and you have added fuel, changed the leaf mass and possibly covered the intumescent seal at the head. Unless the test included that panel, the set is no longer the set that was tested.
Security works the same way: PAS 24 in the UK, or the RC classes under EN 1627, apply to a complete door, and a panel that covers the lock area or thickens the leaf into the rebate is outside the test. If the leaf is 44 mm and the panel 12 mm, the leaf side becomes 56 mm, and that 12 mm has to come out of the rebate or the hinge clearance.
Sound is the third certificate. Rw is a laboratory figure to ISO 717-1 and DnT,w is measured on site, and a gap or a letter plate can dominate both.
The rule: the panel stops at the frame unless the door supplier confirms in writing that the set was tested with the panel. Fluted returns around a reveal are a lining detail; a panel fixed to the leaf is a door modification.
What your RFQ should state
- The board grade named to EN 622-5, and whether it is declared for humid conditions.
- The panel size, thickness and profile depth as ordered, in millimetres.
- The EN 13501-1 report, naming board, face, adhesive, substrate and cavity.
- The fixing schedule: clip type, spacing in millimetres, adhesive and coverage.
- A drawing marking the panels that stay removable for access to services.
- The wall tolerance measured with a 2 m straightedge, and who pays for the pack-out.
- The joint and gap widths, and whether the panel returns onto a fire, security or acoustic door set.
Where this guidance stops
- This article compares material behaviour, not products. Two MDF boards from different factories can differ in density, declared grade and how the edge is sealed.
- A photograph or a sample cannot show board grade, density or whether cut edges were sealed at the factory. Those need a data sheet and an inspection before packing.
- Fire and acoustic results depend on the tested assembly and on the destination's building code. A report is evidence for the assembly it names, not for your wall.
- Foshan Supply coordinates sourcing, sampling and inspection. We do not issue test reports, certify a product, or warrant installed performance; the supplier's declared data governs.
Questions buyers ask
Is MDF suitable for a bathroom wall panel?
Only on conditions. Standard MDF is made for dry conditions, and water reaches it at the cut edge, where the fibre is open. In a bathroom, specify a board declared for humid conditions to EN 622-5, seal every cut edge and the back face, and keep the bottom edge out of standing water. Otherwise use aluminium or PET.
What fire class does a fluted wall panel need?
The class comes from the destination's building code and the use of the room, not from the supplier. Ask for the EN 13501-1 report and check that it names the board, face, adhesive, substrate and cavity, then confirm your wall matches. A report for a bare board does not cover a bonded panel over a cavity.
Can fluted panels be fixed without visible screws?
Yes. Clips, cleats or adhesive behind the groove hide the fixing, and the trade is access rather than appearance. A bonded panel has to be cut out to reach a pipe, while a clipped panel lifts off its cleats. Ask for the load per clip, the spacing and a drawing of the removable panels.
How much does a fluted wall panel weigh?
It depends on the board and its density. At a declared 750 kg/m³ a 12 mm board is 9.0 kg/m², so a 2,400 × 1,200 mm panel of 2.88 m² weighs about 26 kg. Confirm the declared density rather than assuming it, and give the figure to whoever designs the fixing.
Should there be a gap at the floor and the ceiling?
Yes, and the gap is a detail to draw rather than leave to the installer. A floor gap keeps the cut edge out of cleaning water, a ceiling gap lets the panel be lifted into place, and solid timber needs a movement gap across its width. Put the width in millimetres on the drawing.
Can a fluted panel be bonded to a door?
Only with the door supplier's written confirmation. A fire door is certified as a set under EN 1634-1, and a panel adds fuel and thickness to a tested leaf. Ratings such as PAS 24 and EN 1627 also apply to the complete door. If the set was not tested with the panel, stop it at the frame.
How do I calculate how many panels to order?
Divide the wall area by the panel area and round up, then check the height. A 4,800 × 2,700 mm wall is 12.96 m² and a 2,400 × 1,200 mm panel is 2.88 m², so five panels give 14.4 m², about 11% over. A 2,400 mm panel on a 2,700 mm wall leaves a 300 mm band.
Sources
- EN 1634-1 — Fire resistance and smoke control tests for door and shutter assemblies — European Committee for Standardization
- ISO 717-1:2020 — Acoustics: rating of sound insulation in buildings and of building elements — International Organization for Standardization
- BS EN 1627 — Pedestrian doorsets, windows, curtain walling, grilles and shutters: burglar resistance — BSI
- PAS 24 — Enhanced security performance requirements for doorsets and windows — British Standards Institution
- BS EN 13501-1:2018 — Fire classification of construction products and building elements, using data from reaction to fire tests — European Committee for Standardization
- BS EN 622-5:2009 — Fibreboards: specifications, requirements for dry process boards (MDF) — European Committee for Standardization
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 6 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
