In short

A 3D textile wall panel is a roll-goods wallcovering: a textile-faced sheet with a raised or embossed structure, supplied in a roll and specified by roll width and pattern repeat, then adhered to a wall that is flat and primed. It is not a rigid panel with a clip, a shadow gap or a board edge, and it is not bought by the piece.

That distinction changes three parts of the purchase. The unit is the drop, not the panel, so a price per square metre hides how much of the roll the pattern will consume. The wall becomes a specification item, because a relief face follows every ridge underneath it. And the edge becomes a fire and acoustic question, because the wall meets a door set whose certification depends on parts a covering can hide.

01A roll is bought by the drop, not by the square metre

A 3D textile wallcovering arrives as roll goods, so the unit of purchase is a drop cut to the wall height, not a panel lifted from a stack. Roll width and pattern repeat decide how many drops the wall takes; a square-metre price decides nothing until those figures are known.

This is where a wall schedule and a wallcovering quote drift apart. A wall line that says wall panels can be met by roll goods, a fluted MDF module, solid timber slats, or an aluminium or PET extrusion. Each has its own joint, substrate and fire class.

Four relief wall products, the format each is supplied in and the joint each imposes. Substrate and fire class change with the material.
Product Supplied as Joint line What the wall must be
3D textile wallcoveringRoll; width and repeat declaredButted drops, pattern matchedFlat, primed, dry, dimensionally stable
MDF fluted panelRigid moduleGroove or shadow gap, paintedBatten or full adhesive; composite fire class stated
Solid timber slatRigid moduleOpen gap between slatsFixing to studs; movement allowed at edges
Aluminium or PET fluted panelRigid moduleTight module jointFlat substrate; system clip or adhesive

Ask for the fire classification of the finished composite, not of the face material alone, and confirm the substrate the panel system requires.

Decision rule: write the supply format and its joint interval on the schedule line before comparing prices. A module has a joint at every board edge; a roll has a joint at every drop and a pattern to match.

02Roll width fixes the drop count, and the drop count fixes the order

The number of drops is the wall length divided by the usable roll width, rounded up.

Worked example, with dimensions assumed for the arithmetic: a wall 4,200 mm long and 2,700 mm high, a roll 530 mm wide and 10 m long, and 50 mm of trim at head and foot.

  1. Drops: 4,200 ÷ 530 = 7.92, so 8 drops.
  2. Cut length: 2,700 + 50 + 50 = 2,800 mm.
  3. Drops per roll: 10,000 ÷ 2,800 = 3.57, so 3 drops, using 8,400 mm and leaving 1,600 mm.
  4. Rolls: 8 ÷ 3 = 2.67, so 3 rolls, which is 30 m of roll for 22.4 m of drop.
  5. Area check: 11.34 m² of wall against 15.9 m² of roll bought.

The margin is 40% — 15.9 ÷ 11.34 = 1.40 — and it exists because the roll is 530 mm wide while the wall is not a multiple of it.

Decision rule: never deduct a door opening before the drops are laid out. Deduct it from the drop that passes the door, and only if the covering is not carried across the head. If it is carried over, the opening is not a deduction; it is a wall with a hole behind it.

Catalogue reference: 3D textile wallcoverings in the catalogue — models, dimensions and finishes for the directions discussed above.

03Pattern repeat is the number that empties the roll

A pattern repeat adds length to every drop, and that length is paid for at the roll.

A straight match aligns the pattern at the same point on every drop. An offset, or half-drop, match shifts alternate drops by half a repeat, so the waste is uneven. Both are normal; the danger is a quote that names a repeat and never says which match it belongs to.

At a 640 mm straight repeat, each drop must be cut long enough to find the match, so 2,800 + 640 = 3,440 mm. A 10 m roll then yields 2 drops, and 8 drops need 4 rolls, which is 4 × 5.3 = 21.2 m² of roll for 11.34 m² of wall.

Pattern repeat against cut length, drops per 10 m roll and rolls needed for 8 drops, computed from the worked example
Repeat Cut length per drop Drops per 10 m roll Rolls for 8 drops
0 mm (plain)2,800 mm33
320 mm3,120 mm33
640 mm3,440 mm24
1,000 mm3,800 mm24

Cut length is the 2,800 mm drop plus one repeat. Drops per roll is 10,000 mm divided by cut length, rounded down. Rolls is 8 drops divided by drops per roll, rounded up. An offset match adds half a repeat to alternate drops and needs its own line.

Decision rule: count spares in rolls, not square metres. One spare roll from the same batch is the only repair stock that will match.

04The wall has to be flat, and priming is a separate trade

A relief covering does not hide a bad wall; it draws a line along every ridge, and it needs a primed face so the adhesive grabs before the drop dries.

Flatness is made at the jointing stage. A joint left proud, a screw head not sunk, or filler not sanded flat becomes a hard line once a thin textile is glued over it, because the relief follows the substrate rather than bridging it. Hollows are more forgiving than ridges, so the check is made with a straightedge.

Priming is a separate operation with its own drying time. An unprimed board pulls water out of the adhesive before the drop can be brushed out; the failure appears later as a blister, a lifted edge, or a joint that opens in a corridor. Primer and adhesive should come from one system.

The frame is part of the same check. If the covering returns into the reveal, the reveal must be as flat and as primed as the wall, and the frame packed to the finished line, not the plaster line.

The catalogue listed 49 product pages and 83 unique images of 3D textile wallcoverings on 5 November 2026. They show the face, not whether the wall was primed.

Decision rule: make the straightedge check and the primer coat hold points. The roll is not cut until the installer has signed both.

05A fire door is certified as a set, so the covering stops at the frame

A fire door's rating belongs to the door set, which is the leaf, frame, seals, hinges and hardware tested together under EN 1634-1 or the local equivalent, and nothing on the wall should bridge the parts that were tested.

The leaf alone is not the rating. The intumescent seal expands under heat and sits in the frame or leaf edge; where the application needs it, a smoke seal does a different job. Cover the frame face, pack the architrave out so the covering sits flush, or run adhesive into the leaf gap, and the set has been changed. Whether that is acceptable is the door supplier's question, not the wallcovering supplier's.

The detail that keeps both scopes clean is an edge: the covering stops at the architrave or in a shadow gap, the frame face stays visible, and the leaf gap stays as tested. A flush wall with a hidden frame is a door-set decision taken before the frame is ordered.

Decision rule: if the wall line and the frame line are not separated on the drawing, stop and redraw. On site the frame is fixed and the covering is already cut.

06A textile wall does not close the gap that lets the sound out

Acoustic performance is stated as Rw in the laboratory or DnT,w on site under ISO 717-1, and a wallcovering moves neither figure once a gap or a letter plate is in the assembly.

A relief textile absorbs some mid and high frequency sound, which changes how a room sounds, not how much noise crosses the wall. Isolation comes from mass and cavity and, at the door, from the perimeter gap, the seals and every penetration. A gap or a letter plate can dominate the result.

The leaf matters too: a textile wall behind a hollow-core leaf does not make it solid.

Decision rule: where the acoustic requirement is contractual, specify DnT,w for the room with the door set installed and sealed, and inspect the perimeter gap before the covering goes on. Afterwards the gap is hidden.

07Schedule the opening, then the wall, then the covering

One drawing carries the structural opening, the finished wall line and the covering edge. The leaf size is derived from those three.

Three ways a covering meets a door opening, the clear width each leaves, and the line the drawing must carry. Worked on an 838 mm leaf; dimensions in millimetres.
Junction Clear width Drawing must carry
Stops at the architraveUnchanged; the architrave takes the covering edgeArchitrave width and the covering edge line
Returns into the reveal, 3 mm thick6 mm less: 3 mm off each sideReveal depth, covering thickness, frame packing
Carried across the head onlyJambs unchanged; the head loses the covering thicknessHead lining, shadow gap, frame set-out

The covering thickness is a drawing dimension, not a site decision; a return that is not drawn is trimmed on site.

The covering changes the clear opening in one case only: when it returns into the reveal. A return takes the covering thickness off each side it turns, so a 762 mm leaf in a United Kingdom bathroom is the tight case. Decide whether the covering stops at the architrave or turns the corner, and put that on the door schedule.

Entrance doors carry a security rating that varies by market, PAS 24 in the United Kingdom and RC classes under EN 1627, and the cylinder and lock points matter as much as the leaf. A relief wall in an entrance lobby is a finish, not a security measure, and it must not cover the cylinder or the lock.

Decision rule: dimension the covering edge in millimetres on the same sheet as the opening. If the covering thickness is missing, the frame is ordered to the wrong line and the covering is trimmed to hide it.

What your RFQ should state

  1. Supply format: roll goods, with roll width and roll length in millimetres on the quotation, not only a price per square metre.
  2. Pattern repeat in millimetres, straight or offset match, and the cut length per drop at the actual wall height.
  3. The number of drops, cut length per drop and rolls to be delivered, calculated from the wall schedule and opening positions.
  4. Substrate flatness tolerance, joint treatment, primer product and cure time before the first drop is hung.
  5. The straightedge check and primer coat as signed hold points, with the installer's method statement naming the inspector.
  6. Door-set edge detail: covering stops at the architrave or shadow gap; frame face, intumescent seal, smoke seal and leaf gap excluded.
  7. The fire certificate for each set, listing leaf, frame, seals, hinges and hardware tested to EN 1634-1 or the local equivalent.
  8. The acoustic target as DnT,w on site to ISO 717-1 where contractual, with the door set installed and sealed at the test.

Where this guidance stops

Questions buyers ask

What is a 3D textile wall panel?

A roll-goods wallcovering with a textile face and a raised structure, supplied in a roll and specified by roll width and pattern repeat, then adhered to a flat, primed wall. It is not a rigid panel, so the order is counted in drops cut to wall height.

How much extra should I order for pattern repeat?

Work per drop, not per square metre. A 640 mm repeat took the worked example's cut length from 2,800 mm to 3,440 mm, cutting the yield from three drops per roll to two and moving the wall from three rolls to four. Keep one spare roll from the same batch.

Can a wallcovering be hung over a door frame?

No. The rating is certified for the door set: leaf, frame, seals, hinges and hardware tested together under EN 1634-1 or the local equivalent. Covering the frame face or bridging the leaf gap changes the set, and only the door supplier can accept that.

Does a textile wall panel improve sound insulation?

It changes absorption, not isolation. Performance is stated as Rw in the laboratory or DnT,w on site under ISO 717-1, and a gap or a letter plate can dominate. A covering applied after the door is hung cannot close a perimeter gap.

What does a flat, primed wall mean in practice?

Flat means no ridge at a board joint, no proud screw head and no unsanded filler, checked with a straightedge rather than by eye. Primed means a face that will not pull water out of the adhesive too early. Both are signed hold points before the roll is cut.

Can 3D textile wallcovering be used in a bathroom?

Only where substrate, adhesive and ventilation suit the product and the supplier confirms it in writing. A textile face in a wet zone is not a substitute for tiling, and the relief holds dust. Ask for the cleaning method and the exclusions first.

How are the drops joined on a wall?

Drops are butted, pattern matched and cut in place, never overlapped. The joint shows most where light rakes across the wall, so keep it away from the window wall and the door line. Cut length and match type decide where joints land.

Sources

  1. EN 1634-1 — Fire resistance and smoke control tests for door and shutter assemblies — European Committee for Standardization
  2. ISO 717-1 — Acoustics: rating of sound insulation in buildings and of building elements — International Organization for Standardization
  3. EN 1627 — Pedestrian doorsets, windows, curtain walling, grilles and shutters: burglar resistance — CEN-CENELEC
  4. PAS 24 — Enhanced security performance requirements for doorsets and windows — British Standards Institution
  5. BS EN 233:2016 — Wallcoverings in roll form: specification for finished wallpapers, wall vinyls and plastics wallcoverings — British Standards Institution
  6. Fire safety: Approved Document B — HM Government

Pages related to this guide

How this guide was checked

FS

Foshan Supply editorial team · Catalogue indexMethodology

Written in Foshan and reviewed against the catalogue and public standards on 2026-11-05. This page is a buying guide, not a quotation or a warranty. How we work.

How to cite this page: Foshan Supply, “3D textile wall panels: roll, repeat and fixing”, 2026-11-05, https://foshansupply.com/blog/3d-textile-wall-panels/