In short

Outdoor furniture materials are the frame, surface and textile choices that decide how a piece behaves in sun, rain, chlorine and wind: teak and other timbers, powder-coated aluminium, high-pressure laminate (HPL) and woven rope, with stainless fixings and a cushion filling. Each has a different failure mode, and the failure mode is what a buyer is choosing.

A terrace is harder than a kitchen. A chair sits in standing water, in salt spray, in chlorinated splash and in wind that can move it across a slab. The quotation arrives as a photograph, a dimension and a fabric name. What decides whether the piece is sound in three years is a test class, a coating thickness and a fastener grade, and none is visible in the photograph.

01The test class decides what a piece is actually for

EN 581 is the standard most outdoor furniture is tested against, split by product type: part 1 safety, part 2 seating, part 3 tables. The methods behind those parts are EN 1022 for stability and EN 1728 for strength and durability, and non-domestic seating has its own standard, EN 16139.

Outdoor furniture test standards, what each proves, and the question it answers
Standard What it covers Question for a buyer
EN 581-1General safetyTraps, sharp edges, a stable footprint?
EN 581-2Seating, all use levelsTested as seating, at your use level?
EN 581-3Tables, all use levelsTested at the same level as the chairs?
EN 1022Stability of seatingDoes it tip under an edge load?
EN 1728Strength and durabilitySurvives repeated loading and impact?
EN 16139Contract seatingDoes the contract variant meet a higher load?

A report covers a product, a use class and a test house, not a catalogue.

A report belongs to a use class. A chair tested at the domestic level of EN 581-2 does not carry the contract level, even when the frame looks identical; the difference is usually the joint, wall thickness or fastener. A hotel buying 120 rooms is not buying the chair in the photograph.

Decision rule: name the part, the use class and the test house in the RFQ. A reply that quotes EN 581 without a part number answers none of the three questions.

02Teak: the sapwood is where the money goes

Teak is durable because the heartwood carries oily extractives that slow rot and insect attack, not because the timber is called teak. The sapwood, the pale ring under the bark, carries none of them. A frame cut from heartwood outlasts one with sapwood rails, and once oiled they are hard to tell apart.

Grade names vary by mill and mean little between suppliers, so check the material. Teak is a planning reference of roughly 600–700 kg/m³ when dry, so a dense heartwood frame feels heavy for its size. Ask for the declared density and the moisture content at packing.

Decision rule: choose the finish before the species. Bare heartwood weathers to silver-grey and needs an annual wash. Oiled teak keeps the honey colour only if the interval is kept, because a half-oiled frame weathers unevenly.

Catalogue reference: outdoor furniture and terrace seating — models, dimensions and finishes for the directions discussed above.

03Aluminium: the coating is the part that wears

Aluminium does not rust, and that sentence has sold a lot of furniture that fails at a weld. The metal forms an oxide layer that protects it in air; in chloride that layer is attacked, and the powder coat is the barrier that keeps chloride away.

Powder coat chips at an arris, at a weld and where a leg meets paving. A chip is small, but it exposes bare metal, and on a coastal terrace it blooms white and then pits. Matched touch-up paint belongs in the order.

Two measurements turn a claim into a specification: dry film thickness in micrometres, read with a gauge to ISO 2360, and adhesion by cross-cut to ISO 2409. Ask for both on a delivered frame, not a colour card.

Decision rule: at a chlorinated pool or within sight of surf, treat the coating as a service item. Budget for an inspection twice a year and a touch-up at every chip, and put the task in the handover pack.

04Fixings fail before the frame does

Chlorine and salt attack fixings and welds before the frame. A stainless bolt through an aluminium leg is also a galvanic pair: two metals, an electrolyte and a small current, with the aluminium on the sacrificial side. Water in that joint turns a sound frame loose.

Fastener grade and maintenance reference by exposure zone
Exposure Fastener and detail Maintenance reference
Sheltered inland terrace304 stainless, sealed headsRinse and inspect twice a year
Coastal, within sight of surf316 (A4) stainless, isolating washersFresh-water rinse monthly in the dry season
Poolside, chlorinated316 throughout, no mild-steel threadRinse after heavy pool use; check bolts each season
Covered outdoor kitchen316 in the wet zone, IP-rated appliancesWipe down and inspect the gland quarterly

Intervals are planning references for a temperate climate. Local corrosivity, the supplier's schedule and the cleaning contract govern.

The weld is the second weak point, and it is a finishing question more than a strength one. A stainless weld that was not cleaned and passivated shows tea-staining within a season, and the stain runs onto pale paving. On aluminium, poor preparation shows as coating lifting along the bead.

Decision rule: match the fastener to the zone, then state the isolation detail. A nylon washer between stainless and aluminium breaks the galvanic path, and it is the clause most often missing from a quotation.

05HPL: the core and the cut edge are the product

High-pressure laminate is paper and resin pressed under heat and pressure, covered by the EN 438 family. Outdoors it appears as a table top, an outdoor-kitchen door or a bench slat. The face is hard and, in exterior grades, colour-stable; the edge is where water enters.

Compact laminate is solid through the thickness, so a cut edge exposes the same material as the face. A thinner decorative laminate is bonded to plywood or chipboard, and that core swells. Once water reaches a fibre core, the panel grows and the edge lifts.

Thickness is a weight decision too. A 12 mm compact top works out at roughly 17 kg/m² at a density of 1.4 g/cm³: light enough for two people, heavy enough to need a frame rather than four legs. Confirm the weight before designing the base.

  1. Read the edge section: compact reads as one material through the thickness, with no core line.
  2. Check the seal: every cut edge, hinge bore and cable cut sealed, with the product named.
  3. Check the joint: a gap and a drainage path, not a butt joint that holds water against the core.

Decision rule: specify compact grade for any horizontal surface that sees rain, and require sealed edges in writing. HPL with no grade and no thickness is an interior product until proven otherwise.

06Rope and fabric: UV first, water second

Solution-dyed acrylic holds colour under UV better than olefin, because the pigment runs through the fibre rather than sitting in a dyed surface. Lightfastness is tested to ISO 105-B02 and reported on the blue wool scale, where a higher number means slower fading. That result belongs to a colour, not a brand.

Rope is a sleeve over a core. The sleeve takes the UV and the abrasion; the core takes the load. A rope that drains has an open weave and a core that does not hold water, and a wet panel grows mould inside.

Cushions repeat the argument in foam. Open-cell foam with a drainage path dries; a closed block holds water against the cover and grows mould from the inside. A removable cover with a mesh underside and a perforated seat shell does more than any factory stain treatment.

Decision rule: ask for the fibre name, the ISO 105-B02 result on the supplied colour, the foam type and the drainage detail. A supplier who cannot name the fibre is selling a look, and the look will not survive two summers.

07Wind, weight and the slab under the terrace

A pergola, a large parasol or a fixed bench is a structure, and its wind load is a calculation under EN 1991-1-4 and the local code, not a furniture property. The same anchor into a slab, a timber deck or a wall gives very different capacities, and the fixing is usually the weakest link.

On a high-rise balcony the question runs both ways. Wind uplift can move a light chair, and the slab has a load limit that a heavy table, a planter and six people can approach. Neither number comes from the furniture supplier.

An outdoor kitchen adds an electrical question. IEC 60529 codes ingress protection: IP65 is dust-tight and jet-resistant, IP67 allows temporary immersion. The cable gland is often the weak point, so an IP65 enclosure with a lower-rated gland is not an IP65 installation.

Decision rule: get two numbers from the project engineer before choosing the item, the design wind pressure in kN/m² and the permitted imposed load on the slab. Put both in the RFQ and ask for the item weight in kg and the anchorage drawing.

What your RFQ should state

  1. The EN 581 part and use class (domestic, contract or public) the item is tested to, with the test house named.
  2. Timber species, heartwood only, declared density in kg/m³, moisture content at packing and the chain-of-custody certificate number.
  3. Aluminium alloy and temper, powder type, dry film thickness in micrometres with the test method, and one touch-up pen per frame.
  4. Fastener grade by zone (304 or 316), the isolation detail between stainless and aluminium, and the maintenance interval in writing.
  5. For every HPL surface: grade (compact or faced board), nominal thickness in millimetres, and confirmation that all cut edges are sealed.
  6. Rope and fabric fibre names, the ISO 105-B02 result on the supplied colour, the foam type and the cushion drainage detail.
  7. For any anchored item: design wind pressure in kN/m², permitted slab load, item weight in kg and the anchorage drawing.
  8. For an outdoor kitchen: the IP rating of the enclosure and of the cable gland, stated separately under IEC 60529.

Where this guidance stops

Questions buyers ask

Is aluminium outdoor furniture rust-proof?

Aluminium contains no iron, so it does not rust the way steel does. It oxidises, and that oxide protects the surface in ordinary air. In chloride the layer is attacked, which is why the coating and fastener grade matter more than the alloy. A chipped coating lets chloride reach bare metal.

Teak or aluminium for a coastal terrace?

Decide by weight and maintenance rather than prestige. Teak is heavy, warm to the touch and can weather grey untreated, but the honey colour needs regular oiling. Aluminium is lighter and needs no oil, but its coating must be inspected and touched in. On a balcony with a slab limit, weight often decides.

What does EN 581 actually certify?

EN 581 is a test standard with parts for general safety, seating and tables, applied at a domestic, contract or public use level. A report states the product, the part, the use class and the test house. It is evidence of mechanical safety under test, not a warranty against weather or chlorine.

Can HPL be used outdoors?

Compact grade can, when the edges are sealed and the panel drains. A thin decorative laminate on a chipboard core should not be used where rain reaches a cut edge, because the core swells and the face lifts. Ask for the grade, the thickness in millimetres and the edge seal.

How often should coastal furniture be rinsed?

More often than most owners expect, and the interval depends on distance from surf and the salt the wind carries. A fresh-water rinse monthly in the dry season is a reasonable planning reference for a coastal terrace, plus a rinse after a storm. Record who does it.

Does teak need oiling?

Only if you want the honey-brown colour. Left bare, teak weathers silver-grey and needs little beyond an annual wash. Oiled teak needs re-oiling at a fixed interval, and a frame oiled once and then neglected weathers unevenly. Choose one regime and write it into the maintenance schedule.

Why does stainless steel show rust spots?

Usually tea-staining rather than the steel rusting: particles of carbon steel from a grinding disc or a nearby rail settle on the surface and corrode, staining the stainless beneath. A weld that was not cleaned and passivated behaves the same way. The fix is a passivation clean, not a new frame.

Sources

  1. EN 581 — Outdoor furniture: seating and tables for domestic, contract and public use — European Committee for Standardization
  2. EN 1022 and EN 1728 — stability, strength and durability test methods for seating — CEN-CENELEC
  3. EN 16139 — Furniture: strength, durability and safety requirements for non-domestic seating — CEN-CENELEC
  4. EN 1991-1-4 — Eurocode 1: actions on structures, wind actions — European Commission Joint Research Centre
  5. IEC 60529 — Degrees of protection provided by enclosures (IP code) — International Electrotechnical Commission
  6. ISO 105-B02 — Textiles: colour fastness to artificial light, xenon arc fading lamp test — International Organization for Standardization
  7. AAMA 2604 and 2605 — voluntary specifications for organic coatings on aluminium — American Architectural Manufacturers Association
  8. FSC chain of custody — certification for forest products — Forest Stewardship Council

Pages related to this guide

How this guide was checked

FS

Foshan Supply editorial team · Catalogue indexMethodology

Written in Foshan and reviewed against the catalogue and public standards on 2026-11-05. This page is a buying guide, not a quotation or a warranty. How we work.

How to cite this page: Foshan Supply, “Outdoor furniture materials: teak, aluminium, HPL and rope”, 2026-11-05, https://foshansupply.com/blog/outdoor-furniture-materials/