In short
- A vanity carcass is plywood, MDF with sealed edges or moisture-resistant particleboard. The cut edges and the gap at the wall decide more than the board name.
- A wall-hung unit puts the cabinet, the basin, the water and a leaning person onto the wall. The pull-out force at the top fixings is larger than the weight.
- Specify the board, the thickness, every sealed cut, the design load at the front edge, the basin standard and the fan duty at the duct.
A bathroom vanity is a cabinet that carries a basin in a room with running water, high humidity and a floor that is washed. Its carcass is normally plywood, MDF with sealed edges or moisture-resistant particleboard, and the board is only one of four things that decide how long it lasts.
Two vanities built from the same 18 mm board can behave differently within a year, because one has its cut edges sealed before assembly and a gap at the wall, while the other was cut on site and pushed against the plaster. A quotation that names a width and a basin has not named the edge treatment, the fixing load or the gap. Those three lines decide whether the cabinet survives.
01The board name is not the specification
Plywood, MDF and moisture-resistant particleboard can all survive a bathroom, and all three fail once a cut edge is left raw. The board decides how the cabinet behaves while dry; the edge decides what happens when water sits on it.
Plywood is built from crossed veneers. It holds a screw near an edge and moves less than a homogeneous board when the room swings between humid and dry. Its weakness is the ply line: water at a raw edge wicks between veneers and the board delaminates. MDF machines and paints cleanly, but a raw edge takes water and stays swollen. Moisture-resistant particleboard copes with occasional damp but swells fastest at an unsealed cut.
| Board | What it does well | Where it fails in a wet room | Clause for the RFQ |
|---|---|---|---|
| Plywood, 18 mm | Holds a screw at an edge; stable in humid air | Delaminates along a raw ply edge | Board type, thickness, edges sealed before assembly |
| MDF, 18 mm | Machines and paints cleanly; uniform core | Swelling at a cut edge that does not reverse | Sealed edges plus a moisture-resistant grade named in writing |
| MR particleboard, 18 mm | Flat and stable; widely available | Takes up water at an unsealed cut or fixing hole | Edge band and sealant schedule; no on-site cutting |
A board can be moisture-resistant and still fail at a cut. The grade describes the panel, not the cabinet.
Decision rule: specify the board by type, nominal thickness and edge treatment, and treat the phrase 'moisture-proof board' as an unanswered question.
02Water reaches a vanity along four paths
Four paths carry water into a vanity: the basin cut-out, the waste and trap penetration, the joint where the top meets the wall, and the floor when the room is washed. Splash gets the attention, but the other three do more damage.
The arithmetic is small. A 900 mm wide, 480 mm deep top with a 500 × 400 mm basin cut-out loses 0.2 m² of surface to the hole, and every millimetre of that perimeter is a raw edge until somebody seals it. The same applies to the waste hole and the hinge fixings.
- Seal the carcass cut edges before assembly, not after the cabinet is built.
- Seal the basin and waste cut-outs on site, including the inside face of the hole.
- Draw the wall gap: a cabinet pushed hard against uneven plaster cannot be sealed, cleaned or ventilated.
Decision rule: require an edge-sealing schedule that names who seals which cut, at which stage of the build, and with what. A schedule with no names is a request, not a specification.
Catalogue reference: bathroom vanity units in the catalogue — models, dimensions and finishes for the directions discussed above.
03A wall-hung unit loads the wall, not the floor
A wall-hung vanity turns the wall into the cabinet's floor, and the pull-out force at the top fixings is larger than the weight on the brackets because the load hangs forward of the wall.
A 900 mm carcass uses roughly 2.6 m² of 18 mm board: 0.047 m³ and, at an assumed 650 kg/m³, about 30 kg before a top is fitted. Top, basin, water and leaning person are added, and the sum sizes the fixing.
| Component | Reference mass | Basis |
|---|---|---|
| Carcass, 18 mm ply, 900 mm wide | About 30 kg | 2.6 m² of board at 0.018 m and 650 kg/m³ |
| Stone top, 20 mm, 900 × 480 mm | About 22 kg | 0.43 m² at 50 kg/m² |
| Ceramic basin | Confirm with the supplier | Ask for the packed weight, not the carton size |
| Water in basin and trap | About 5 kg | A basin holds roughly 5 litres when full |
| Person leaning on the front edge | 30 kg | An assumption to state, not a rule |
| Sum of the example | About 100 kg | Round up, then design the wall for it |
Substitute the supplier's declared masses. The sum and its lever arm size the anchors; the individual figures do not.
Decision rule: put a design load in kilograms at the front edge into the RFQ, and require the wall build-up, anchor type and bracket spacing on the approved shop drawing. Masonry, a stud partition with blocking and a lightweight block wall need three answers.
04The basin joint is the part that leaks first
The joint between the top and the basin is the first place a vanity leaks and the last thing a quotation describes.
An integrated top removes the joint but fixes the basin shape. An inset basin needs a cut-out and a rim seal, and water past the rim runs into an unsealed edge. An under-mounted basin hangs from brackets, so the bracket carries the load. A vessel basin raises the waste and throws splash beyond the top. The basin should be declared to EN 14688.
| Mounting | What it demands | Common failure | Clause |
|---|---|---|---|
| Integrated | A moulded one-piece top | A chip or craze at the rim | Material and basin standard named |
| Inset | A cut-out and a rim seal | Water past the rim into a raw cut edge | Sealant type, joint width, who applies it |
| Under-mounted | Brackets or a frame; polished cut-out | A loosened bracket under a heavy basin | Bracket rating and fixing detail on the drawing |
| Vessel | A top deep enough for the splash | Water beyond the top and behind the unit | Top depth and tap reach in millimetres |
One joint, one trade, one name. A sealant applied by whoever is on site last is the usual cause of a leak behind a top.
Weight follows the top: a 1,200 mm top in 20 mm stone is about 0.58 m² and about 29 kg at 50 kg/m², before a basin hangs under it. Decision rule: name the mounting, the joint width in millimetres, the sealant and who applies it, and require the trap access opening to be drawn.
05Damp air needs a route out of the carcass
Give the cabinet an air path and size the extract fan at the duct, not the grille. A closed cabinet in a wet room dries only as fast as the room does, and the fan is the only thing moving that air.
A 2.4 × 2.0 × 2.4 m bathroom holds 11.5 m³. A fan rated 15 l/s, or 54 m³/h, changes that air about 4.7 times an hour — one air change every 13 minutes — before a flexible duct with two bends takes its share.
- Fan quoted only at the grille: ask for the duty at the duct termination in litres per second.
- Door fits tight: cut an undercut, record it in millimetres, or the fan has nothing to draw.
- Cabinet has a sealed back panel: leave a service gap so the carcass can dry.
Decision rule: state the fan duty in litres per second at the duct termination, the duct diameter and route, and the door undercut in millimetres. An answer that quotes only the fan has not answered the question.
06The mirror is judged by vertical light at the face
Judge the mirror by the light that reaches the face, not by the room's lux figure. A ceiling downlight behind the viewer lights the top of the head and leaves the face in shadow however bright the room is.
Two figures belong in the schedule: vertical illuminance at face height, and the colour rendering index of the lamp. A fitting at face height on both sides of the mirror or across its top puts light where the face is; a downlight in the ceiling puts it behind the person standing there. Record the kelvin too, because 3000 K and 4000 K in one room read as two schemes.
- Tiled wall, no chasing: specify a mirror with integrated light and a driver access point.
- Separate wall lights: fix the centre height and the distance from the mirror edge on the elevation.
- Glass specified to EN 12150-1 or EN ISO 12543: every hole goes on the drawing, because toughened glass cannot be drilled after processing.
Decision rule: record the fitting position at face height, a minimum CRI, the kelvin value and the glass standard with hole positions; where a lighting designer has set a lux target, that figure governs.
07The RFQ, the shop drawing and the check on arrival
One page carries a vanity: the board and its edges, the wall load, the joint, the air and the light.
- Name the board, the thickness in millimetres, and the edge-sealing schedule with the stage for each cut.
- State the design load in kilograms at the front edge, with wall build-up, anchor type and bracket spacing.
- Draw the wall gap and the top joint, and name the trade that seals it.
- Name the basin mounting and the basin standard (EN 14688), and show trap access.
- State the fan duty in litres per second at the termination, the duct route and the door undercut.
- State the mirror light position, CRI and kelvin, and the glass standard with hole positions.
On arrival, open one cabinet and look at a cut edge before the rest is unwrapped. A sealed edge carries a continuous band or a coat that wraps the corner; an unsealed one shows the core. Check the door reveals with a straightedge before the top is fitted: a twisted box is a wall problem before it is a carcass problem.
What your RFQ should state
- Carcass board by type, nominal thickness in millimetres and the grade it is declared to.
- An edge-sealing schedule naming each cut, the stage it is sealed and the product used.
- The wall gap and the top joint drawn, with the trade that seals it named.
- A design load in kilograms at the front edge, with wall build-up, anchors and bracket spacing.
- Basin mounting and the basin standard (EN 14688), plus the trap access opening.
- Fan duty in litres per second at the duct termination, the duct diameter and the door undercut.
- Mirror light position at face height, a minimum CRI and the kelvin value.
- Glass standard (EN 12150-1 or EN ISO 12543) with every hole on the drawing before processing.
Where this guidance stops
- This article describes carcass construction and specification, not specific products. Two vanities in the same board can differ in glue line, edge band and panel density.
- A photograph cannot show whether an edge is sealed, what the core is, or how the wall was built. Those need a data sheet, a sample and a shop drawing.
- Plumbing, wiring and ventilation rules differ by market; local regulations and the project's engineer govern the numbers here.
- The load example uses assumed masses; it illustrates a method, not a structural design for any wall.
- Foshan Supply coordinates sourcing, sampling and inspection. We do not test boards, issue certificates, design walls or install vanities; the supplier's data and the agreed inspection scope govern.
Questions buyers ask
Which carcass material should I choose for a bathroom vanity?
Choose by how the edge will be treated, not by the board alone. Plywood holds fixings at an edge; MDF gives a clean painted face but swells at a raw cut; moisture-resistant particleboard is flat and stable if every cut is sealed. In a room that is washed down, plywood with sealed edges is the most forgiving.
Is MDF suitable for a bathroom vanity?
It can be, behind a sealed finish and with sealed edges. MDF machines and paints well, which is why it is common on painted doors. Its failure mode is water at a raw edge: the panel swells and does not return to thickness. Specify a moisture-resistant grade, seal every cut, and keep the cabinet off a wet floor.
Do wall-hung vanities need special wall support?
Yes. The wall carries the cabinet, the basin, the water and anyone leaning on the front edge, and the load hangs forward of the wall, so the pull-out force at the top fixings is larger than the total weight. Blocking or a frame must be designed for that load, and the anchors belong on the shop drawing.
How do I stop water getting into a vanity carcass?
Seal every cut edge before assembly, then seal the basin and waste cut-outs on site, including the inside face of the hole. Draw the joint where the top meets the wall and name who seals it. Leave a gap at the wall so the cabinet can be cleaned and ventilated, and keep a cold pipe from dripping onto it.
Does a bathroom vanity need an extract fan?
The room needs one, and the cabinet benefits. A fan is rated in litres per second or cubic metres per hour at a stated pressure, but the duct route and the door undercut decide how much air moves. Ask for the duty at the duct termination, not the grille, and check that air can enter under the door.
What light should go above a bathroom mirror?
Light at face height, on both sides of the mirror or across its top, rather than a ceiling downlight behind the viewer. Record vertical illuminance at face height and the CRI of the lamp. A CRI of 90 or above is a reasonable floor where skin and colour are judged, and the kelvin should match the room.
Should a basin be integrated or inset?
An integrated top removes the joint at the basin and fixes the shape. An inset basin is easier to replace but needs a cut-out and a rim seal. An under-mounted basin keeps the top clean but hangs from brackets. Decide by who maintains the room and how the joint seals, not by appearance alone.
Sources
- EN 14688 — Sanitary appliances: wash basins, functional requirements and test methods — British Standards Institution
- EN 14527 — Shower trays for domestic purposes — British Standards Institution
- EN 14428 — Shower enclosures: functional requirements and test methods — British Standards Institution
- EN 14891 — Liquid-applied water impermeable products for use beneath ceramic tiling — European Committee for Standardization (CEN-CENELEC)
- EN 12150-1 — Thermally toughened soda lime silicate safety glass — European Committee for Standardization
- EN 817 — Sanitary tapware: mechanical mixing valves (PN 10), general technical specifications — British Standards Institution
- CEN construction sector — harmonised standards and the Construction Products Regulation — European Committee for Standardization
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 7 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
