In short
- Lippage is the step between adjacent tile faces at a joint. For rectified porcelain, 1 mm under a straightedge is the usual acceptance threshold; polished faces are held tighter.
- Most lippage is built in before tiling: a substrate more than 3 mm out of flat over 2 m, coverage below 90–95%, or a warped tile body.
- Put the step number, the joint width and the measuring method in the RFQ. A 2–3 mm rectified joint and a 1 mm limit cannot both be argued after grouting.
Lippage is the height difference between two adjacent tile surfaces at a joint, measured with a straightedge laid across the joint and a feeler gauge underneath. It is a construction defect more often than a tile defect: the step comes from the substrate, the bed and the joint.
It matters because it is the first thing a client sees. A polished floor reflects a window along the joint line, and a 1 mm step breaks that reflection into a ridge no grout hides. By then the floor is grouted, and the repair is to cut tiles out.
01Lippage is built in before the first tile is bedded
Most lippage on a large format floor comes from the substrate and the bed, not the tile. A flat floor tolerates a slightly warped tile; a floor with a hollow does not.
The working figure is 3 mm under a 2 m straightedge. That is not generous for a 1,200 mm tile: 3 mm over 2 m is the same order of size as the step you are avoiding, so a floor at the limit has spent its tolerance. Check both directions and the diagonal.
The tile contributes too. A pressed body can leave the press with a slight bow, and rectifying does not remove it: the saw cuts the perimeter, the face keeps its curve. Two tiles face to face show the bow; side by side it becomes a step.
| Cause | What appears on site | Check before grouting | Who carries the cost |
|---|---|---|---|
| Substrate hollow over 3 mm in 2 m | Steps recurring in one direction, often mid-room | 2 m straightedge on bare screed, both ways and diagonal | Screed or levelling contractor |
| Spot-bonded adhesive | Alternating high and low tiles, hollow under a tap | Lift one tile per room, photograph the back | Tiler |
| Warped tile body | A step repeating at every joint in one direction | Two tiles face to face; factory flatness declaration | Supplier, if the declared figure is exceeded |
| Joint tight for the size variation | Lines that wander, then a step where the tiler corrects | Measure five tiles against nominal | Specifier, if the joint was set too narrow |
The cost column assumes a conventional supply-and-fix contract. Know which party owns the remedy while the floor is still open.
02The 1 mm rule and the method that gives it meaning
A 1 mm step at a joint is the usual acceptance threshold for rectified porcelain. It is close to the width of the grout line, so the step is about the size of the feature meant to disguise it.
The number needs a method: a 2 m straightedge across the joint at right angles, a feeler gauge of the agreed thickness, and the worst reading rather than the average. A gauge that will not slide under anywhere passes; one that slides under at three joints fails.
Across a 3 mm joint, a 1 mm rise is a gradient of 1 in 3. Underfoot it is a ridge; in raking light, a shadow line. A polished face reflects a window head, and the eye reads that break, so polished surfaces are held tighter than 1 mm.
| Finish | Typical joint | How the step reads | What to agree |
|---|---|---|---|
| Rectified, matt | 2–3 mm | A visible ridge in raking light | 1 mm maximum, straightedge and feeler gauge |
| Rectified, polished | 2–3 mm | A break in the reflection across a room | Tighter than 1 mm, lighting condition named |
| Rectified, textured | 3 mm | Texture hides the step but traps dirt at the low edge | 1 mm, plus a cleaning trial |
| Non-rectified | Wider joint | The wider grout line breaks the reflection | 1 mm, with a joint to match measured variation |
These are planning references for a specification conversation, not a code citation. The destination standard and the project specification govern.
Catalogue reference: tiles and porcelain formats — models, dimensions and finishes for the directions discussed above.
03Joint width absorbs what the tile cannot
Rectified tiles are cut to a calibrated size after firing, which is what makes a 2–3 mm joint possible. A porcelain body at 0.5% absorption or below, group BIa under ISO 13006:2018, takes up little water, so the joint and the size variation are the variables. Non-rectified tiles leave the kiln with more variation, and the joint has to absorb it.
The choice is a trade: a tile has a nominal size and an actual size, and the difference has to go somewhere. Widen the joint and the difference disappears into the grout line. Hold 2 mm on an uncalibrated body and it goes into the layout instead: the tiler shifts tiles to keep the line true, and each shift is a potential step.
The arithmetic is easy. Ten tiles across a 6 m run, each 0.5 mm over nominal, add 5 mm to the run, so the line cannot be both parallel to the wall and 2 mm wide everywhere. Ask for the calibrated size and permitted variation, then set the joint from the measurement.
A brick bond on a bowed tile puts a high edge against a low edge, so the pattern multiplies the step. Dry-lay a square metre and look along it at a shallow angle.
04Adhesive coverage decides whether the bed can be flat
Large format tiles generally need a C2TE-class adhesive to EN 12004 and full coverage of at least 90–95%. Coverage is the easiest part of a specification to claim and the hardest to see.
Under EN 12004, C is cementitious, 2 is improved bond strength, T is thixotropic, meaning resistance to slip, and E is extended open time. A brand name proves nothing; the class does.
Take a 1,200 × 600 mm tile, which is 0.72 m². At 90% coverage with a 3 mm bed after compaction, the volume is 0.72 × 0.90 × 0.003 m³, about 1.9 litres per tile. Across 100 m², at 139 tiles, that is roughly 270 litres before waste; at 6 mm, about 540 litres. A thick bed is not a substitute for a flat substrate.
Back-buttering, a flat coat on the tile back over the combed bed, closes the pores and lets the ridges spread. To check it, lift one tile per room before the adhesive sets, photograph the back, and compare bare patches with the 90–95% requirement.
05The failures that arrive after handover
The lippage that costs money is the one that grows. A 1 mm step at handover is a snag; the same joint two years later, with a chipped edge and a hollow beneath, is a repair.
A void under one corner takes the point load of a chair leg. The face is brittle in tension and the corner chips. Water reaches the void, the bond fails, and the tile moves underfoot. Replacing it means cutting out a tile locked in on four sides, and a later batch matches neither shade nor height.
Deflection and water are the accelerants. On a suspended timber floor the structure, not the tile, sets the step: the floor moves and the joints open. Outdoors a lipped joint holds water at its low edge, and water plus freeze–thaw breaks paving. A tile is not frost-resistant because the catalogue says exterior; an ASTM C1026 report decides that.
Slip is separate. DIN 51130 groups ramp slip resistance from R9 to R13 and DIN 51097 uses A, B and C for barefoot wet areas, but neither is a complete assessment. Wet DCOF to ANSI A326.3 is the measurement; 0.42 is the common reference for level interior floors, not ramps.
06Inspection before grouting is the cheap moment
Lippage is provable only if it is measured before grouting, at positions both sides agreed. After grouting, the argument is about opinion.
- Mark a grid on the plan and number the rooms, so every reading has an address.
- Lay a 2 m straightedge across the joints at right angles, then on the diagonal.
- Push the agreed feeler gauge under it and record the worst reading, not the average.
- Photograph the gauge with the room number in shot; a photograph without a scale proves nothing.
- Tap along each tile edge and mark hollow spots in a second colour.
- Record tile batch, adhesive class and trowel notch on the same sheet.
- Sign with the tiler before grouting, listing tiles to be lifted.
One reading per 10 m², plus every joint crossing a doorway or change of substrate, is a workable sampling rule. For 100 m² that is ten readings and a marked plan, an hour on site against the cost of lifting a grouted floor. Ask for ASTM C648 strength and C373 absorption reports for the batch, not the series.
07The RFQ that gives lippage an owner
Lippage needs four things in the document: a number, a method, a sampling rule and a named person. Without them it is a matter of taste, and taste loses to the schedule.
| Item | What to write | Why it matters |
|---|---|---|
| Substrate | 3 mm maximum under a 2 m straightedge | Fixes the tolerance budget before a tile is opened |
| Adhesive | C2TE to EN 12004, notch size stated | Coverage is invisible once the tile is down |
| Coverage | 90–95% minimum, one tile lifted per room | Turns a claim into a check |
| Joint | 2–3 mm rectified, variation declared | Joint width and lippage trade against each other |
| Step | 1 mm maximum, tighter on polished faces | The number the snag list will be argued against |
| Remedy | Lift and relay at the installer's cost | The clause that gives the number force |
Attach the same schedule to the purchase order and the fixing contract. A tolerance that binds one party only is not enforceable at handover.
The last row is the one that gets dropped. A number with a method, a sampling rule and a signature is a specification; without them it is advice.
On a project sourced from Foshan the division is simple: the factory declares the tile, the installer owns the bed, the buyer owns the acceptance criteria. Two of those sit in the buyer's hands before the first tile opens.
What your RFQ should state
- Substrate: 3 mm maximum deviation under a 2 m straightedge, any direction, measured before tiling.
- Adhesive: C2TE to EN 12004, with the trowel notch in millimetres and back-buttering in the scope.
- Coverage: 90–95% minimum, verified by lifting one tile per room before the adhesive sets.
- Joint: 2–3 mm for rectified tiles, with calibrated size and variation declared by the factory.
- Step: 1 mm maximum at any joint, tighter on polished faces, measured with straightedge and feeler gauge.
- Sampling: one reading per 10 m², plus every threshold, doorway and change of substrate.
- Records: batch, adhesive class, notch size and readings on one sheet signed before grouting.
- Remedy: tiles outside the limit lifted and relaid at the installer's cost, same batch.
Where this guidance stops
- This describes practice, not a specific product. Tiles from different factories differ in flatness, calibrated size and warpage.
- A photograph cannot show a 0.5 mm step, a hollow under a tile or the coverage on the back. Those need a straightedge, a feeler gauge and a lifted tile.
- The 1 mm figure is a common acceptance threshold, not a code requirement in every market; local standards govern, and a polished face needs its own agreed number.
- Frost, slip and exterior suitability depend on the body, the finish and the fixing system; an R rating is not a test report.
- Foshan Supply coordinates sourcing, sampling and inspection. We do not install tiles, issue test reports or certificates, or offer a universal warranty.
Questions buyers ask
What causes lippage in large format tile installation?
Usually the substrate and the bed, not the tile. A floor more than 3 mm out of flat under a 2 m straightedge forces the tiler to bridge or pack, and each correction becomes a step at a joint. Spot-bonded adhesive, a bowed body and a joint too narrow for the size variation end the same way.
Is 1 mm lippage acceptable on a porcelain floor?
For rectified porcelain, 1 mm at a joint is the usual acceptance threshold, measured with a 2 m straightedge and a feeler gauge. Polished surfaces are normally held tighter, because the reflection magnifies the step. It is a reference rather than a code: write the number, the finish and the method into the specification.
Does a wider joint hide lippage?
It helps when size variation is the cause. A wider joint absorbs that variation, so the tiler keeps both the line and the joint without shifting tiles. It does not fix a hollow substrate or a spot-bonded bed, and it does not remove a step already there.
What adhesive should be used for large format tiles?
A C2TE-class adhesive to EN 12004: cementitious, improved bond strength, thixotropic for slip resistance, with extended open time. Coverage should reach 90–95%, applied with a notched trowel plus a flat coat on the tile back. The notch size belongs in the quote, because the notch decides how much adhesive touches the tile.
Can lippage be fixed after grouting?
Only by cutting the affected tiles out, and the replacements rarely sit at the same height. That is why readings are taken before grouting, when a tile can still be lifted without damage. Grout can be raked out and refilled, but the tile edge cannot be lowered without removing the tile.
Does lippage matter on a wall?
Yes, though the tolerance is discussed differently. Wall tiles are read at eye level in grazing light, so a step that would pass on a floor can be obvious beside a mirror or above a vanity. Large panels also hold water at a lipped edge in a shower, making the step a maintenance point as well.
How is lippage measured on site?
Lay a 2 m straightedge across the joint at right angles, then on the diagonal, and push a feeler gauge of the agreed thickness underneath. Record the worst reading at each position, not an average, and photograph the gauge with the room number visible. One reading per 10 m², plus every threshold, is a workable rule.
Sources
- ISO 13006:2018 — Ceramic tiles: definitions, classification, characteristics and marking — International Organization for Standardization
- ANSI A326.3 — Test method for measuring dynamic coefficient of friction of hard surface flooring — Tile Council of North America
- ASTM C648 — Standard test method for breaking strength of ceramic tile — ASTM International
- ASTM C373 — Standard test methods for determination of water absorption and bulk specific gravity of ceramic tile — ASTM International
- EN 12004 — Adhesives for ceramic tiles: classification and requirements — European Committee for Standardization
- ASTM C1026 — Standard test method for measuring the resistance of ceramic tile to freeze-thaw cycling — ASTM International
- DIN 51130 and DIN 51097 — Slip resistance testing of floor coverings, standards catalogue — Deutsches Institut für Normung
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 7 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
