In short
- Kitchen ergonomics is the arithmetic of three numbers: worktop height, clear aisle width and reach. All three are fixed on the elevation, before the order is placed.
- The worktop is a stack: plinth, carcass, top. A 100 mm plinth, 720 mm carcass and 40 mm top give 860 mm; a 150 mm plinth gives 910 mm.
- Clearance is a subtraction: room width minus both runs. Two 620 mm runs in a 2,400 mm room leave 1,160 mm, above the 1,015 mm pass-through minimum.
Kitchen ergonomics is the study of the distances a cook's body needs: how high the worktop sits above the finished floor, how much clear floor stands between opposing runs, and how far a hand reaches without stepping forward. It turns a plan and an elevation into a short list of dimensions a factory can hold.
Those dimensions are decided before the order and rarely appear on the quotation. A kitchen built from 18 mm panels and good hinges can still be tiring, because the tiring part is arithmetic: a plinth 50 mm too low, an aisle 200 mm too narrow, a shelf above the reach band. Every figure below is a worked example; substitute your drawing and redo the sum.
01The worktop is a stack of three numbers
Worktop height is not a product attribute. It is a sum: plinth plus carcass plus top, ordered from three drawings, and the quotation rarely states the total.
Take a 100 mm plinth, a 720 mm carcass box and a 40 mm stone top. The surface lands at 860 mm. Raise the plinth to 150 mm and the same box gives 910 mm. Nothing there is a standard: it is a choice of three numbers, and only the plinth has adjustment left on site.
| Plinth | Carcass | Top | Worktop height | Where it belongs |
|---|---|---|---|---|
| 100 | 720 | 40 | 860 | The common European stack |
| 100 | 720 | 20 | 840 | A thin slab top on a full substrate |
| 150 | 720 | 40 | 910 | A tall cook, or a deep floor build-up |
| 150 | 780 | 40 | 970 | A standing-height island or larder run |
Height is measured from the finished floor, not the structural slab. A tile bed and a screed change every figure in the column.
Decision rule: write the finished floor level on the elevation before the plinth height. A 20 mm tile bed over a 40 mm screed raises the floor by 60 mm, and every height in the room moves with it.
02The 865 mm ceiling decides the whole run
Where a covered dwelling unit has to be accessible, the work surface is capped at 865 mm above the floor, with an adjustable counter permitted between 735 mm and 915 mm (ADA Standards 804.3.2). General work surfaces take the same 865 mm maximum under 902.3; a lower height is a design choice, not a figure the standard sets.
That cap collides with the stack above. 865 − 720 − 40 = 105 mm of plinth, a shallow toe space with no allowance for floor build-up. The alternative is a second height in the same run: a 760 mm wide section at 865 mm with knee space 685 mm high and 280 mm deep at 230 mm (306.3), and the rest at 910 mm.
Decision rule: one worktop height per run, or a documented step with a section drawing. Two heights in one continuous top need a joint, and a joint in a working surface collects water.
Settle this before door style or worktop material. One accessible unit pulls the whole block to 865 mm, and a block built at 910 mm cannot be corrected later without moving the splashback and the housings.
Catalogue reference: kitchen cabinet ranges and carcass options — models, dimensions and finishes for the directions discussed above.
03Aisle width is a subtraction from the room
Clear aisle is a subtraction. Measure the room's clear width, subtract the depth of both runs to their furthest projecting face, and exclude handles. The advisory to 804.2 measures the same way.
The ADA figures are 1,015 mm between opposing runs in a pass-through kitchen, 1,525 mm inside a U-shaped kitchen, and 915 mm for an accessible route. All three are minimums for a wheelchair, not targets for a household.
| Room width | Both runs | Clear aisle | What it allows |
|---|---|---|---|
| 2,000 | 1,240 | 760 | One cook; the dishwasher door blocks the way when open |
| 2,200 | 1,240 | 960 | One cook; above the 915 mm route minimum |
| 2,400 | 1,240 | 1,160 | Two people passing; above the 1,015 mm figure |
| 2,700 | 1,240 | 1,460 | Below the 1,525 mm U-shape figure; a galley that works |
620 mm is a 600 mm carcass plus a 20 mm top overhang. Handles add their projection; the standards exclude hardware, but the person standing at the open door does not.
The appliance door is what the subtraction misses. A 600 mm dishwasher door drops into the aisle, and the cook stands in the same 600 mm. In a 1,160 mm aisle that leaves 560 mm.
Decision rule: draw the plan with the dishwasher, oven and refrigerator doors open. If any open door crosses the aisle centre line, the kitchen is single-cook.
04The work triangle is a perimeter you can walk
The work triangle is the path between sink, hob and refrigerator. It is drawn as a shape and argued as a shape; the useful version is a perimeter in metres.
Labelled calculation on a worked example: sink to hob 1,800 mm, hob to refrigerator 2,400 mm, refrigerator to sink 3,000 mm. The circuit is 1,800 + 2,400 + 3,000 = 7,200 mm, or 7.2 m. Shorten the sink–hob leg to 1,200 mm and it is 6.6 m. The arithmetic holds for your legs; the answer does not travel.
The legs are not equal in cost. The sink–hob leg is walked with a full pot, the hob–refrigerator leg with both hands full, and the refrigerator–sink leg decides where the preparation space can sit.
- Sink to hob: the loaded leg, and the shortest of the three.
- Hob to refrigerator: keep it clear of the aisle centre line.
- Refrigerator to sink: the leg that sets the preparation run.
Decision rule: no leg is set by symmetry with the elevation. Move the appliance on the plan, re-measure all three, and check that none crosses an open door. RFQ clause: the plan shall dimension all three legs and draw the door swings.
05Reach sets wall cabinet and oven heights
A standing reach is a band, not a point: 1,220 mm maximum and 380 mm minimum above the floor for an unobstructed reach (308.2.1, 308.3.1), and storage has to sit inside a reach range (811.3).
That makes wall cabinet height a reach decision rather than a style one. A 720 mm tall cabinet hung with its underside at 1,400 mm has its carcass top at 2,120 mm and its top shelf just below. The shelf is outside the band, so it becomes storage reached from a step.
Ovens follow the same band. A single oven with its cavity centre at 1,200 mm sits inside it; a stacked pair pushes the upper cavity above 1,220 mm. Where the unit must be accessible, the standard route caps the freezer instead: at least 50% of freezer space within 1,370 mm (804.6.6).
Decision rule: dimension the top shelf, the oven cavity centre and the microwave shelf from the finished floor, then check each against 1,220 mm. Anything above it is bulk storage and should be named as such.
06Inside the box, millimetres decide capacity and load
Carcass thickness is quoted as a headline and behaves as a clearance. An 18 mm box 600 mm wide has 564 mm of internal width, a 16 mm box has 568 mm, and a 12 mm drawer box has 576 mm. The 16 mm box is 4 mm wider inside and, because stiffness rises with the cube of thickness, about 30% less stiff ((16 ÷ 18)³ = 0.70).
18 mm is the common European carcass thickness, 16 mm is common in budget exports, and 12 mm is usually a back or a drawer box. Density turns thickness into weight, which is what a hinge sees on every opening.
| Board | Density | Area weight at 18 mm | Fails first at |
|---|---|---|---|
| Particleboard | 650–750 kg/m³ | 11.7–13.5 kg/m² | An unsealed cut edge by a sink or a wet plinth |
| MDF | 700–800 kg/m³ | 12.6–14.4 kg/m² | A machined edge, where the fibre ends are open |
| Plywood | 500–700 kg/m³ | 9.0–12.6 kg/m² | A wet edge that delaminates the veneers |
Area weights are calculated from the density range and rounded. None of the three boards is waterproof: particleboard swells permanently, MDF swells most at a cut edge, and plywood tolerates intermittent damp but can delaminate.
Hardware is sold by brand and rated by series. Hinges and runners are tested under EN 15570 and EN 15338, and the series sets the load and cycle figure. A full-height door over about 2,100 mm needs a straightening profile or a second hinge set, or it bows and rubs at the top corner.
Decision rule: 18 mm panels for any run carrying a worktop, 16 mm only where the box is short and lightly loaded, 12 mm only for backs and drawer boxes.
Evidence travels with the panel. CARB ATCM Phase 2 and US EPA TSCA Title VI regulate formaldehyde emissions from panels and finished goods, and both apply to imports into the United States. Europe names EN 312 for particleboard, EN 636 for plywood and EN 622-5 for MDF, with E1 the common class. The assembled unit is tested separately: KCMA A161.1, or ANSI/BIFMA X5.9 for storage.
07What goes on the drawing and into the RFQ
The elevation carries the heights and the plan carries the clearances. A quotation without both prices doors and a worktop area.
| Clause | What to write | Why it changes the price |
|---|---|---|
| Floor | Finished level and build-up, with heights measured from it | The plinth is the only on-site adjustment |
| Worktop | One height per run, or a dimensioned step | A second height means a second top |
| Clearance | 1,015 mm between opposing faces, or the project figure | Decides whether the run is single-cook |
| Reach | Top shelf and oven cavity centre on the elevation | Changes cabinet heights and door sizes |
| Carcass | 18 mm panels to EN 312 E1, with declared density | Sets stiffness, weight and fixing |
| Hardware | Hinge and runner series, EN 15570 and EN 15338 | Sets the door height limit |
| Evidence | Panel certificate, hardware list, 1:5 section | Proof that the quote is the product |
ISO 3055 coordinates kitchen equipment sizes; ask which module the supplier builds to before you fix the plinth and carcass figures in this table.
- Measure the room, including the floor build-up, and write the level on the drawing.
- Fix the worktop height per run and check it against 865 mm if the unit must be accessible.
- Subtract both runs from the room width and record the aisle with doors open.
- Mark the top shelf, oven cavity centre and freezer against 1,220 mm and 1,370 mm.
- Send the marked drawings with the RFQ and require them back annotated.
Decision rule: approve the plan and elevation before the deposit and keep them for the site check. A door sample is a finish check.
What your RFQ should state
- Finished floor level and build-up, with every height measured from the finished floor.
- Worktop height as one figure per run, or a dimensioned step with its joint position.
- Clear aisle measured with the dishwasher, oven and refrigerator doors open.
- The three work-triangle legs dimensioned on the plan, with appliance door swings drawn.
- Top shelf, oven cavity centre and freezer heights checked against 1,220 mm and 1,370 mm.
- 18 mm carcass panels to EN 312 E1 with declared density, plus CARB Phase 2 and TSCA Title VI evidence for US import.
- Hinge and runner series with EN 15570 and EN 15338 ratings, and a straightening profile on any door over 2,100 mm.
- Annotated elevation and plan returned with the quotation, plus one approved production sample.
Where this guidance stops
- This article gives design arithmetic, not anthropometric data. The height that suits a household depends on the people who cook; the worked examples show the method, not a figure for your body.
- The 1,015 mm, 1,525 mm, 865 mm, 1,220 mm and 1,370 mm figures come from the US ADA Standards and apply where those standards, or a local equivalent, are in force. A local code or a hotel brand standard may set a different figure, and that document governs.
- A drawing cannot show whether the delivered carcass is 18 mm or 16 mm, whether the board is E1, or whether the hinge is the series specified. Those need a sample, a panel certificate and a hardware list.
- Clearances depend on the finished floor, the wall plumb and the appliance installed. A 20 mm difference in floor build-up moves every height in this article.
- Foshan Supply coordinates sourcing, sampling and inspection. We do not design kitchens, certify products or install them, and no figure here is a warranty of fit.
Questions buyers ask
What is kitchen ergonomics?
Kitchen ergonomics is the set of dimensions that decide how a kitchen fits the person using it: worktop height, the clear aisle between opposing runs, and the band a standing hand can reach. Each is fixed on the drawing and each can be checked with a tape measure.
What is a normal worktop height?
There is no single standard, because a worktop is plinth plus carcass plus top. A 100 mm plinth, 720 mm carcass and 40 mm top give 860 mm; a 150 mm plinth gives 910 mm. Where accessibility applies, the work surface is capped at 865 mm.
How wide should the aisle between kitchen runs be?
The ADA Standards require 1,015 mm between opposing runs in a pass-through kitchen, 1,525 mm inside a U-shaped kitchen, and 915 mm for an accessible route. Those are minimums for a wheelchair. For two cooks, what matters is what remains with the dishwasher door open.
What is the correct work triangle?
There is no accepted total length. The triangle is a perimeter: add the sink–hob, hob–refrigerator and refrigerator–sink legs from your plan. A worked example of 1,800, 2,400 and 3,000 mm gives 7.2 m per circuit. Judgement belongs on which leg carries a load.
How high should wall cabinets be hung?
High enough to clear the worktop and splashback, low enough that the top shelf stays inside the reach band. With a 1,220 mm maximum reach, a 720 mm tall cabinet hung at 1,400 mm puts its top shelf above the band.
Does carcass thickness change anything I can feel?
Yes, in two ways. A 16 mm box is 4 mm wider inside than an 18 mm box of the same outside width, and it is about 30% less stiff in bending, because stiffness falls with the cube of thickness. The second effect is the one you notice: drawers that rack and doors that rub.
Can a tall oven housing be built too high?
Yes. A cavity centre above 1,220 mm is outside the standard reach band, and a stacked pair usually puts the upper oven there. Where the unit must be accessible, the standard route caps the freezer instead, with at least 50% of freezer space within 1,370 mm.
Sources
- Americans with Disabilities Act — Accessibility Standards (2010), sections 306, 308, 403, 804 and 902 — U.S. Access Board
- BS ISO 3055:2021 — Kitchen equipment: coordinating sizes — British Standards Institution
- Formaldehyde — US Environmental Protection Agency
- Composite wood products program — California Air Resources Board
- KCMA certification and A161.1 — Kitchen Cabinet Manufacturers Association
- BIFMA standards and ANSI/BIFMA X5.9 — BIFMA
- European standards and technical committees — European Committee for Standardization
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 7 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
