In short
- Kitchen cabinet MOQ is set per component line: carcass boards, door fronts, drawer boxes, profiles and hardware each carry a separate minimum from a different work centre.
- A width change is only a cutting change and usually holds the minimum; a thickness change or a door over 2,100 mm is a new component and raises it.
- Ask for the minimum per line in the factory's own unit, and for the certificate that names the board standard; one project MOQ figure hides both.
Kitchen cabinet MOQ is the smallest quantity a factory will produce of one component line — a carcass set, a door style, a drawer box — before the set-up cost of that line is spread over too few units. It is not one number for a kitchen, and it is rarely the same number for two components in the same order.
Buyers meet the problem at quotation stage. Three suppliers return three totals and three different conditions, and the totals are compared as though they described the same order. The useful comparison is narrower: which component sets the floor, and what would have to change in the design to clear it.
01The minimum belongs to a work centre, not to your kitchen
A kitchen touches four component lines: the saw and edgebander that make the carcass, the door line, the drawer-box line, and the bench that kits hinges and runners. Each has a set-up, paid for by the units that follow it.
The set-up is physical. A saw needs a cutting list and a first-article check; an edgebander needs tape width and glue colour; a paint line needs a clean-down between colours; a drilling centre needs a hinge programme. None of it scales with the cabinet count, and all of it is divided by it.
Two suppliers can therefore quote the same kitchen with minimums that differ widely and both be truthful: one is quoting the carcass, the other the door finish.
Decision rule: ask for the minimum per line, in the unit the factory schedules — carcass sets, door leaves, board area, hardware cartons — then ask which line your project is shortest of.
Clause for the RFQ: state the MOQ per component line, the unit of measure, and whether it applies to the order or to each finish and size within it.
02Three boundaries separate a standard cabinet from a custom one
Standard size ends at three points, and only the first is about millimetres. Width and height can be cut from the same 18 mm board; a thickness, a tall door or a hardware series changes the product.
- The cutting boundary. A narrower carcass uses the same 18 mm panel, edgebanding and hinge series. Only the cutting list and drilling programme change, so the minimum usually holds.
- The board boundary. Moving to 16 mm, or to 12 mm for a back or drawer box, changes the panel purchase, the edgebanding set-up, the drilling depth and the paperwork. The minimum follows the board.
- The component boundary. A door over about 2,100 mm, a new hinge series or an extruded profile is a new part with its own tooling and its own minimum.
Custom quotes usually mix all three. A 16 mm carcass, a door above 2,100 mm and a non-catalogue veneer is three new products compared against a standard kitchen.
| Change | What resets | Line that sets the floor |
|---|---|---|
| Width or height only | Cutting list; drilling | Carcass board |
| 18 mm to 16 mm | Panel; edgebanding; drilling depth | Board mill |
| 18 mm to 12 mm back | Panel; machining; fixing | Board mill |
| Door over about 2,100 mm | Drilling; straightening profile | Door line |
| New finish | Clean-down; sample; batch | Door line |
| New hinge series | Drilling pattern; carton | Hardware carton |
The floor moves to whichever line is reset. A change that resets two lines meets two minimums, not one.
Catalogue reference: kitchen cabinet ranges and carcass options — models, dimensions and finishes for the directions discussed above.
03Thickness and density decide the freight before quantity does
Mass per square metre is thickness times density, and the spread between panel types is wider than the step from 18 mm to 16 mm. At 700 kg/m³, 18 mm board weighs 12.6 kg/m²; at 16 mm, 11.2 kg/m², about 11% less.
| Panel | Density (kg/m³) | 18 mm | 16 mm | 12 mm | Position |
|---|---|---|---|---|---|
| Particleboard | 650–750 | 11.7–13.5 | 10.4–12.0 | 7.8–9.0 | Carcass |
| MDF | 700–800 | 12.6–14.4 | 11.2–12.8 | 8.4–9.6 | Painted fronts |
| Plywood | 500–700 | 9.0–12.6 | 8.0–11.2 | 6.0–8.4 | Sink runs |
Mass = thickness in metres × density, rounded. Edgebanding, glue and hardware are excluded; confirm the supplier's declared panel weight before designing fixings or freight.
Density decides whether a wall cabinet hangs on a given fixing, what the shipment weighs before crating, and whether one person can lift a door. Between the lightest plywood and the densest MDF at 18 mm, the difference is around 60% on the figures above.
Decision rule: require the declared density in kg/m³ and the mass per square metre on the data sheet, then check both against the fixing and the freight before negotiating quantity.
Thickness is also a fixing question. A 16 mm panel leaves less material around a hinge screw than an 18 mm panel, and a 12 mm back will not carry the same fitting as an 18 mm side. That is one reason to hold thickness constant across a run rather than vary it line by line for cost.
04A door above about 2,100 mm starts a second product
A full-height door over about 2,100 mm needs a straightening profile or a second hinge set to avoid bowing. That moves the door out of the standard programme into a component with its own drilling, hardware count and minimum.
Bowing is slow. A tall leaf on two hinges carries its weight top and bottom while the middle has nothing holding it straight. Humidity, a veneer that takes up moisture on one face, and a handle load pull it away from the carcass, and the gap opens along the middle of the run.
The profile is a metal section set into a groove in the back of the door; a second hinge set shares the load. Both are specified per height, so a standard drawing cannot simply be scaled.
Decision rule: measure every door. Any leaf over about 2,100 mm goes on its own schedule line with hinge positions, straightening method and quantity, priced and approved separately.
05Moisture rules out some boards before quantity matters
No carcass board is waterproof, and moisture behaviour sets where the cabinet can go. Particleboard swells permanently once water reaches the core; MDF swells most at a cut edge; plywood tolerates intermittent moisture but can delaminate; stainless steel is the commercial answer.
| Material | When wet | At a cut edge | Where it belongs |
|---|---|---|---|
| Particleboard | Swells permanently | Absorbs fastest | Dry interior runs |
| MDF | Swells, worst at exposed edges | Weakest point | Painted fronts |
| Plywood | Tolerates intermittent moisture | Can delaminate | Sink runs, sealed edges |
| Stainless steel | Unaffected | Folded, not cut | Commercial kitchens |
Suitability is a property of the assembly: board, edge seal, fixing and drainage together.
The edges decide the outcome. A sealed edge, a back detail that keeps water off the core and a sink run set so a leak drains forward matter more than the board name. A 12 mm back is a saving in material, not a moisture barrier.
Decision rule: name the wet zones in the RFQ — sink run, dishwasher bay, boiler cupboard, wash-down area — and require the board, edge seal and fixing detail for each.
06Compliance documents travel with the batch
Formaldehyde rules attach to the panel and the finished good, so a board change resets the paperwork. CARB ATCM Phase 2 and US EPA TSCA Title VI cover panels and finished goods and both apply to imports into the United States; the EPA rule is at 40 CFR Part 770. In Europe, EN 312 covers particleboard, EN 636 plywood and EN 622-5 MDF, with E1 the common class.
Certificates are issued for a board, a supplier and a production period, not for a kitchen design. A factory buying certified board in a mill run cannot switch board for a short run without a new document trail, and a finish applied elsewhere adds a second link.
The risk is a cabinet compliant as a board and undocumented as a finished good. Ask for the certificate naming the board standard and the panel supplier, and the declaration covering the assembled unit.
Decision rule: state the destination and the regulation in the RFQ, and require the certificate for the exact board and thickness. A class name without a panel standard or a certificate number is not evidence.
07Hardware is rated by series, and a series has a carton
Hinges and runners are tested under EN 15570 and EN 15338, and the series, not the brand, sets the load and cycle rating. Two hinges from one brand can sit in different series with different ratings and carton quantities.
So hardware carries a second minimum. A series change can alter the drilling programme on every door and the number of cartons the factory buys. At unit level, KCMA A161.1 is the North American cabinet performance standard and ANSI/BIFMA X5.9 covers storage units.
A procedure that makes the comparison work:
- List the components: carcass, door, drawer box, profile, hardware.
- For each, state the standard and the thickness or series, not the brand.
- Ask for the minimum in the factory's own unit, per line and per finish.
- Name the boundary changes on the drawing: any thickness, any door over about 2,100 mm, any new series.
- Require the certificate for the board and the declaration for the finished cabinet.
- Ask what happens to the minimum if one line is reduced after the order is placed.
Six answers make two quotes comparable. Without them, a lower total may describe a smaller order than the one you placed.
What your RFQ should state
- The MOQ for each component line separately, with the unit of measure and whether it applies per order or per finish.
- The carcass thickness in millimetres, 18 mm or 16 mm, and the declared density in kg/m³ for the panel supplied.
- Every door over about 2,100 mm listed on its own line with hinge positions and the straightening method.
- The panel standard as a number, EN 312, EN 636 or EN 622-5, and the certificate reference for the exact board.
- The formaldehyde route for the destination: CARB ATCM Phase 2 and TSCA Title VI for the United States, E1 for Europe.
- The hinge and runner series by name, with the EN 15570 and EN 15338 rating claimed for that series.
- The board, edge seal and fixing detail for each wet zone: sink run, dishwasher bay, boiler cupboard.
- Which component line sets the floor for your design, and what the factory would have to change to lower it.
Where this guidance stops
- There is no universal kitchen cabinet MOQ. The figure depends on the factory, the component, the finish and the month, so this article explains the mechanism rather than quoting a number for your order.
- A photograph or a sample door cannot show board density, edge sealing or the certificate behind the panel. Those need a data sheet, a cut sample and a certificate reference.
- Compliance depends on the destination and on the workshop that finishes the cabinet. A panel certificate does not by itself cover an assembly made in another building.
- Hardware ratings are series-level and laboratory-based. Site humidity, door weight and use change service life beyond the test.
- Foshan Supply coordinates sourcing, sampling, inspection and shipping. We do not manufacture cabinets, issue certificates or warranty installed performance, and we publish no MOQ; the factory sets it per line.
Questions buyers ask
What is the MOQ for custom kitchen cabinets?
There is no single figure. A factory sets a minimum per component line — carcass panels, door fronts, drawer boxes, profiles, hardware cartons — because each line has its own set-up. Your order is governed by whichever minimum your design is furthest from meeting, so ask for each one separately.
Does a custom width increase the minimum order?
Usually not. A different width in the same 18 mm board is a cutting-list change and a new drilling programme, and the panel comes off the same run. A change of thickness, door height, finish or hardware series is what moves the minimum, because each resets a different line.
Why is 18 mm the standard carcass thickness?
It is the common European carcass thickness and the one most hinge, runner and edgebanding tooling is set up for. 16 mm appears in budget export work, and 12 mm is often used for backs or cheap drawer boxes. A 16 mm box is about 11% lighter at the same density, but it is a different board specification.
Can I mix 16 mm and 18 mm carcasses in one order?
You can, but treat it as two board specifications rather than one kitchen. Each thickness is a separate panel purchase, a separate edgebanding set-up and a separate certificate, so the order carries two minimums. Check whether the saving survives the second set-up.
Is particleboard acceptable in a kitchen?
Yes, in dry runs with sealed edges, and it is the common carcass board in European kitchens. It swells permanently once water reaches the core, so the sink run, the dishwasher bay and any leak path need a board and edge detail chosen for moisture. MDF behaves similarly; plywood can delaminate.
Which documents prove formaldehyde compliance?
For the United States, a certificate to CARB ATCM Phase 2 and TSCA Title VI naming the board and the panel supplier, plus the declaration covering the finished good. For Europe, the panel standard — EN 312, EN 636 or EN 622-5 — and the E1 class claimed for that board. A class name alone is not evidence.
Do tall doors need a different minimum?
Yes, when a leaf exceeds about 2,100 mm. At that height the door needs a straightening profile or a second hinge set to avoid bowing, which brings its own drilling, hardware count and profile length. Put those doors on a separate line so quantity and price stay visible.
Sources
- Formaldehyde — US EPA — US Environmental Protection Agency
- Formaldehyde emission standards for composite wood products (40 CFR Part 770) — US Environmental Protection Agency
- Composite Wood Products Program — California Air Resources Board
- KCMA — Kitchen Cabinet Manufacturers Association — Kitchen Cabinet Manufacturers Association
- BIFMA — standards for furniture and storage — BIFMA
- CEN — European standards for wood-based panels and hardware — European Committee for Standardization
- Composite Panel Association — panel standards and grading — Composite Panel Association
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 7 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
