In short
- A hardware tier is a position inside one manufacturer's range, not a brand. The same badge covers hinge families with different tested loads and cycle levels.
- EN 15570 tests hinges and EN 15338 tests runners; a report proves something only when it names the series, the load and the cycles.
- Door mass, carcass thickness and drawer load decide which series survives, and a door above 2,100 mm needs a straightening profile or an extra hinge.
A hinge or runner tier is the position a hardware family occupies inside one manufacturer's catalogue: one brand sells several hinge families and several runner families, each with its own article number, tested load and cycle level.
The distinction changes a purchase because a kitchen quotation can read 'Blum soft close' and still mean a family chosen for stock availability rather than for the mass of the door it carries. The badge is the part that can be printed without changing anything behind it.
01The badge is a brand; the series is the product
A brand name in a quotation is a promise about where the parts were bought, not about which part is in the box. One brand can sell several hinge families that look identical at arm's length.
The tiers are not a ladder from bad to good. An entry family from a European brand and a mid family from a Chinese manufacturer can both be tested to the same standard at the same level. A higher family buys adjustment range and spare-part supply, not a different physical principle.
| Tier as quoted | What the line usually means | Hinge evidence to demand | Runner evidence to demand |
|---|---|---|---|
| Brand name only | Any family in the range, chosen by stock position | Series and article number, with the EN 15570 report | Series, extension and the EN 15338 report |
| Brand and series | A named family, often the entry family sold into projects | Article number, tested load, cycle count, damper part | Article number, load per pair at the stated extension |
| Brand, series and sample | A family handled and approved on a sample door | Approval sheet with the article number and door mass | Approval sheet with the box width, load and extension |
The labels describe quotation practice, not factory quality. The carton carries an article number, and that number must match the approved sample.
The rule is blunt: reject any hardware line that names a brand without a series and an article number. One email fixes it, and a factory can no longer substitute a cheaper family without changing a document you hold.
02EN 15570 and EN 15338 test a series at a stated load
EN 15570 covers strength and durability of hinges and their components, for hinges pivoting on a vertical axis. EN 15338 covers extension elements, which is what a drawer runner is. Both are type tests on a component, not an approval of the cabinet.
A report is useful only if it names the series, the load applied, the cycle count and the mounting. One manufacturer can publish different levels for different families, which is why the series is the specification and the logo is not.
| Standard | Applies to | Test unit | What it does not prove |
|---|---|---|---|
| EN 15570 | Hinges pivoting on a vertical axis | One hinge, cycled under a stated load | That the carcass holds the plate screws |
| EN 15338 | Extension elements and their components | One runner pair at a stated extension | That the drawer box survives the cycles |
| KCMA A161.1 | Assembled kitchen cabinets, North America | A complete cabinet, tested as a unit | Component compliance of a hinge family |
| ANSI/BIFMA X5.9 | Storage units | A complete storage unit | Kitchen use, moisture or panel emissions |
The levels are set by the report for the series supplied, so the load and cycle count must be read from that document rather than assumed from the brand.
A door opened eight times a day runs 2,920 cycles a year, or 29,200 over ten years. In a hotel room, opened twenty times a day, it reaches 7,300 a year and 73,000 over ten. That is arithmetic on stated assumptions, not a test result, but it separates domestic and contract expectations.
The clause: 'Hinges shall be brand [X], series [X], article [X], with an EN 15570 report stating the test load and cycle count. Runners shall be brand [X], series [X], article [X], rated for [X] kg per pair at [X] mm extension, with an EN 15338 report.'
Catalogue reference: kitchen cabinet ranges in the catalogue — models, dimensions and finishes for the directions discussed above.
03Soft close is a damper, and it wears on its own
Soft close describes a damper, not a load rating. The damper is a small cylinder or an elastomer piston that slows the last part of the swing; it carries none of the door mass and changes nothing about tested durability.
The damper is usually the first part to weaken; the hinge itself stays sound. The symptom, a door that swings freely and then bangs, reads as a failure but is a worn part. An integrated damper is replaced with the hinge; a clip-on damper has its own number.
Temperature changes the feel as well. Damping is viscous, so the same hinge closes faster in a cold room than in a warm showroom, and a summer demonstration is not a test of a door on a north-facing wall.
04Door mass and carcass thickness decide the hinge
A hinge carries a lever, so the decision variable is door mass rather than width or colour. Two doors of the same size in different panels can differ by kilograms.
| Door size (mm) | Area (m²) | Mass at 18 mm (kg) | Per hinge, 2 hinges (kg) | Per hinge, 3 hinges (kg) |
|---|---|---|---|---|
| 600 × 720 | 0.43 | 5.4 | 2.7 | 1.8 |
| 600 × 1,400 | 0.84 | 10.6 | 5.3 | 3.5 |
| 600 × 2,100 | 1.26 | 15.9 | 7.9 | 5.3 |
| 900 × 2,100 | 1.89 | 23.8 | 11.9 | 7.9 |
Calculation: area × 0.018 m × 700 kg/m³, the middle of the 650–750 kg/m³ particleboard range. Glass, handle and edge banding are excluded, so a glazed door is heavier than its row.
Height adds a second problem. A full-height door over about 2,100 mm needs a straightening profile or a second hinge set, because it bows between fixings even when each hinge is inside its tested load.
The panel behind the plate is half of the joint. 18 mm is the common European carcass thickness, 16 mm is common in budget exports and 12 mm is often used for backs and cheap drawer boxes. Particleboard at 650–750 kg/m³ and MDF at 700–800 kg/m³ behave differently at an edge; MDF swells most at a cut edge, and a hinge cup is a cut edge. Which holds a screw better is a pull-out question, and the supplier should answer it with a test.
The rule: send door size, thickness, panel and glass mass with the enquiry, then ask for the mass per hinge at the tested load.
05Runners: the load class belongs to the extension
A runner rating is only meaningful with the extension it was measured at. The load on the fixings grows as the drawer comes out, so a figure without an extension cannot be compared with another figure.
The drawer box is the other half, and cheaper quotes save there first. A 12 mm box side takes the runner screws with little material around them, and a box that flexes puts the load into the fixings rather than the base.
- Side-mount roller runners hang the drawer from the cabinet sides, so the side panel and the roller share the load.
- Concealed undermount runners carry the box on its base, and the fixing at the back of the box is where the load path ends.
- Full extension puts the drawer outside the cabinet, which is the position of maximum load on the front fixing.
- A runner screwed to a 16 mm side panel has less material around each screw than on an 18 mm panel.
The clause: 'Runners shall be rated for [X] kg per pair at [X] mm extension, with an EN 15338 report naming the series; drawer boxes shall be [material] at [X] mm, with the runner fixing shown on the shop drawing.' The screw positions decide whether the rating survives installation.
06A branded hinge on an undeclared board still stops at customs
Hardware and panel are bought on separate lines, and the paperwork tends to follow only one of them. CARB ATCM Phase 2 and US EPA TSCA Title VI regulate formaldehyde emissions from composite wood panels and finished goods, and both apply to imports into the United States. In Europe, EN 312 covers particleboard, EN 636 covers plywood and EN 622-5 covers MDF, with E1 the common emission class.
Upgrading the hinge and downgrading the board is a familiar shape of value engineering. The hinge report says nothing about the panel and the panel declaration says nothing about the hinge, so one annex has to carry both. A border official reads the panel declaration; a guest reads the door.
Moisture decides the board more than the brand does. Particleboard swells permanently when wet, MDF swells most at cut edges, plywood tolerates intermittent moisture but can delaminate, and stainless steel appears where a commercial kitchen washes down the fronts.
The rule: one annex, three lines, covering panel standard and class, hardware brand/series/article, and the moisture exposure of the room. The thicknesses that matter, 18 mm carcass, 16 mm budget export and 12 mm back or drawer box, belong on the drawing rather than in the brochure.
07Auditing a sample door before you approve it
A sample door is where hardware, board and workmanship meet before the container is packed. Twenty minutes with a screwdriver and a set of scales settles more than a catalogue page.
- Read the article number stamped on the hinge and on the runner, and write both on the approval sheet.
- Weigh the door, divide by the number of hinges, and compare with the mass per hinge in the report.
- Open and close the door ten times; a working damper slows the door before it meets the carcass.
- Load the drawer to its declared load, pull it to full extension and watch the gap at the back of the box.
- Check the plate screws for a raised ring or a split at the cup, which is what a thin panel looks like under load.
- Ask for the EN 15570 and EN 15338 reports for the series you have just read, and check that the codes match the labels.
Record all of it. A sample approved on appearance alone can be replaced by a cheaper family unnoticed, and by then the container is on the water.
What your RFQ should state
- Panel standard and class for every board: EN 312, EN 636 or EN 622-5, with the E1 or TSCA Title VI declaration the destination requires.
- Panel thickness by part: 18 mm carcass, 16 mm where specified, and backs or drawer boxes stated separately.
- Hinge brand, series and article number, with the door mass and the number of hinges per door.
- The EN 15570 report for that hinge series, naming the test load, the cycle count and the mounting.
- Runner brand, series and article number, with the load per pair in kilograms and the extension in millimetres.
- The EN 15338 report for that runner series, with the drawer box material and thickness.
- A statement of which parts are damped, whether the damper is integrated or clip-on, and the spare-part number.
- The approved sample record, carrying article numbers, door mass, drawer load and report references.
Where this guidance stops
- This article explains how tiers and test reports differ. It does not rate any brand's current range, and a manufacturer can change a series without changing the badge.
- A test report is evidence for the sample tested. It does not cover the cabinet, the board, the fixing or the way a door is loaded in service.
- The load and cycle level have to be read from the report for the series supplied; no pass threshold is quoted here, because the level varies by family and market.
- Foshan Supply coordinates sourcing, sampling and inspection. We do not test hardware, issue reports or certificates, or warrant installed performance.
Questions buyers ask
Is Blum better than Hettich?
Neither brand is a single product, so the comparison has no answer at brand level. Both sell several hinge and runner families, and the tested load and cycle count belong to the series rather than the logo. Ask for the article number and the EN report, then compare mass per hinge, extension and spare parts.
What does soft close mean on a cabinet hinge?
It means a damper slows the last part of the swing. The damper is a wear part, either integrated into the hinge cup or clipped on, and it does not increase the load the hinge can carry. A soft-close hinge can still be an entry-level hinge, and the damper is usually the first component to weaken.
How many hinges does a tall cabinet door need?
Enough that each hinge carries a share of the mass inside its tested load, and above about 2,100 mm the door also needs a straightening profile or a second hinge set because it will bow between fixings. Work out the door mass first, divide by the hinge count, then check that figure against the report.
Do I need EN 15570 for cabinets sold in the United States?
Not as a legal requirement. The US route runs through KCMA A161.1 for cabinet performance, ANSI/BIFMA X5.9 for storage units and TSCA Title VI for panel emissions. An EN report is still useful component evidence, but the destination code governs.
Can I mix hinge and runner brands in one kitchen?
Yes, and it is common. The two systems do not interact, so the decision is about mounting plates, spare parts and how many suppliers you want to chase. What you should not mix is a series inside one door: hinges on the same door should share an article number, or it will hang unevenly as they wear.
Why do drawer runners feel rough after two years?
Usually because the runner is loaded beyond its rating at the extension actually used, or because the box has loosened at its fixings and is twisting the runner. Debris and a dry track make it worse. Check the load per pair, the extension, the box material and whether the screws still hold before blaming the runner.
Does a branded hinge mean the cabinet passes KCMA A161.1?
No. KCMA A161.1 tests an assembled cabinet rather than a component, so a hinge report cannot carry a cabinet through it. The hinge is one input alongside the board, the joint, the drawer and the finish. A supplier claiming cabinet-level compliance should show the cabinet test, not the hardware catalogue.
Sources
- Formaldehyde and TSCA Title VI — requirements for composite wood products — US Environmental Protection Agency
- Composite wood products — ATCM Phase 2 regulation — California Air Resources Board
- KCMA A161.1 — Recommended performance and construction standards for kitchen and vanity cabinets — Kitchen Cabinet Manufacturers Association
- ANSI/BIFMA X5.9 — Storage units — BIFMA
- CEN — European standards for furniture hardware — European Committee for Standardization
- NS-EN 15570:2008 — Hardware for furniture: strength and durability of hinges and their components, hinges pivoting on a vertical axis — Standards Norway
- DIN EN 15338:2024-12 — Hardware for furniture: strength and durability of extension elements and their components — DIN Media
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 7 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
