In short
- CARB Phase 2 is California's formaldehyde emission limit for composite wood panels, and TSCA Title VI applies the same four limits across the United States.
- The limits are 0.05 ppm for hardwood plywood, 0.09 ppm for particleboard, 0.11 ppm for MDF and 0.13 ppm for thin MDF, measured in a chamber.
- An E1 certificate, a product photograph and a verbal assurance prove nothing. The bundle label, the named chamber report and the importer's entry file do.
CARB Phase 2 is the second tier of California's formaldehyde emission standard for composite wood products, set out in the Airborne Toxic Control Measure at Title 17 of the California Code of Regulations, section 93120. TSCA Title VI is the federal rule at 40 CFR Part 770, which adopts the same limits for hardwood plywood, particleboard and medium-density fibreboard sold in the US.
Because the limit attaches to the panel rather than the finished object, the duty moves along the chain: the producer certifies and labels, the importer holds the records, the fabricator inherits the same duty, and the retailer produces documentation on request. A wardrobe is never certified. The boards inside it are, and the paperwork follows them from press to shop floor.
01The limit sits on the panel, not on the wardrobe
CARB Phase 2 covers three panel types: hardwood plywood, particleboard and medium-density fibreboard, including thin MDF. It does not cover the cabinet, the door or the bed frame as an object, though those products are built from the panels it covers.
That is why the duty spreads. The panel producer certifies and labels. An importer of finished furniture keeps records showing the panels comply. A fabricator who turns panels into carcasses keeps the same records for three years, and a retailer produces them when an inspector asks.
Several wood products sit outside the rule, and buyers assume otherwise: hardboard, structural plywood made to PS 1 or PS 2, oriented strand board, structural composite lumber, glued laminated timber, finger-jointed lumber and solid wood. Wood packaging is outside it, and falls under ISPM 15 for plant health rather than TSCA.
Decision rule: list every substrate by panel type, not by trade name. Plywood on its own is unresolved, because hardwood plywood is in scope and structural plywood is not. A supplier who cannot say which one is quoted has not finished the specification, and the gap surfaces at entry, not at the sample stage.
02Four numbers carry the whole rule
The regulation reduces to four limits, identical in the California measure and the federal rule. Everything else in the file exists to show that a bundle met the number for its panel type.
| Panel type | Limit (ppm) | Approx. equivalent (mg/m³ at 23 °C) | Where it usually appears |
|---|---|---|---|
| Hardwood plywood | 0.05 | 0.061 | Cabinet doors, drawer boxes, decorative wall panels |
| Particleboard | 0.09 | 0.110 | Wardrobe carcasses, shelving, worktop substrate |
| Medium-density fibreboard | 0.11 | 0.135 | Routed doors, mouldings, painted panels |
| Thin MDF (8 mm and under) | 0.13 | 0.160 | Drawer bottoms, back panels, curved skins |
The milligram column is a conversion, not a second standard: 1 ppm of formaldehyde is about 1.23 mg/m³ at 23 °C and 101.3 kPa, derived from a molar mass of 30.03 g/mol. European certificates use different test conditions, so treat the column as orientation only.
A purchase order that says low formaldehyde has said nothing a factory can be held to. One that says particleboard components shall meet TSCA Title VI and CARB Phase 2 at 0.09 ppm, tested to ASTM E1333, with the report naming the producing plant, can be checked at the loading bay without an argument about adjectives.
Decision rule: name the panel type and its limit in the PO line, not in a covering email. A wardrobe mixes a particleboard carcass with MDF doors, so write two lines and two limits. The thin MDF limit is the one most often missed, because drawer bottoms and back panels are bought as offcuts and never specified.
Catalogue reference: sourcing, inspection and shipping coordination — models, dimensions and finishes for the directions discussed above.
03The bundle label is the evidence you collect first
A compliant panel leaves the press with a label. Under the federal rule it carries the producer's name, a lot or batch identifier and a statement that the panels comply with TSCA Title VI. Panels made with no-added-formaldehyde or ultra-low-emitting-formaldehyde resins carry a different designation: those routes are exempt from routine emission testing, not from certification, labelling or recordkeeping.
The label is fixed to the bundle, and the bundle is what the fabricator cuts up; by the time the cabinet reaches a showroom, the label is in a bin. It is the most common documentation failure in a furniture order, and costs nothing to avoid.
Decision rule: photograph every bundle label at loading, name the file with the purchase order line and the date, and treat an unlabelled bundle as a rejected bundle rather than a discount. Ask for the photograph before the container is sealed, because a label photographed in your own warehouse proves where the panel ended up, not where it came from.
04A test report is only valid for what it names
Compliance rests on a chamber test. ASTM E1333 is the large-chamber reference method; ASTM D6007 is the small-chamber alternative, linked to it by correlation rather than identical numbers. A factory may run a desiccator check for daily control, but a desiccator result is not the compliance result, and a report citing only a factory method will not survive a customs query.
| Field | What the report must state | What a weak report says instead |
|---|---|---|
| Product | Panel type, thickness and face or core construction | A series name or a product family |
| Resin | Resin system, including any NAF or ULEF claim | Low emission, without a resin description |
| Plant | The producing plant and its identifier | The trading company or the brand |
| Method | ASTM E1333 or D6007, with the test date | Complies with CARB, no method |
| Certifier | The third-party certifier and its scope | A laboratory logo with no scope |
| Validity | The certification period the report sits inside | A report older than the current certificate |
A report for a 12 mm panel does not cover an 18 mm panel from the same press, and a report for a urea-formaldehyde resin does not cover a phenol-formaldehyde one. Thickness and resin are part of the tested article.
Decision rule: reject any report that does not name plant, thickness and resin. Those three fields turn a certificate into evidence, and their absence signals a document issued for a different product.
05E1, E0 and F☆☆☆☆ do not convert into Phase 2
Most Chinese panel suppliers answer a formaldehyde question with a European or Japanese grade, because that is what their export file contains. The grades are real, but the test and the units are not the same.
The European E1 limit is 0.124 mg/m³ under the EN 717-1 chamber method, roughly 0.10 ppm. Set that against the American limits: a board that passes E1 at 0.10 ppm fails the 0.09 ppm particleboard limit, and clears the 0.11 ppm MDF limit by a margin too thin to survive a retest. E0 is an industry grade around 0.05 mg/m³ with no legal standing in the US. The Japanese F☆☆☆☆ grade is a desiccator result in mg/L under JIS A 1460.
Decision rule: accept only an ASTM chamber report for the American market, and treat any certificate in mg/m³ or mg/L as a prompt to ask for the underlying report. A grade name is a claim about a test; it is not the test.
06The entry file decides whether the container clears
Compliance is checked twice: at the factory gate by the certifier, and at the border by the importer of record. The second check stops containers, and depends on who is named importer under the delivery term.
Under FOB or CIF the buyer is importer of record and must hold the certification and the records. Under DDP the seller takes that position, which sounds convenient until it cannot produce a certification in its own name. Incoterms 2020 allocates delivery, cost and risk; it does not allocate regulatory responsibility.
Three other regimes sit in the same file and are often confused. Classification: a finished cabinet is furniture, while the panel alone falls in the wood chapter, and the ten-digit HTS code decides both the duty rate and whether an additional Section 301 tariff applies to Chinese-origin goods. Packaging: the crate is solid wood packaging needing the ISPM 15 mark on the wood, which says nothing about the panel inside. Timber due diligence: a European buyer also needs EUDR due diligence and geolocation, and a TSCA certificate does not satisfy EUDR any more than EUDR satisfies TSCA.
Decision rule: put the importer of record, the ten-digit HTS code and the certificate number on the proforma invoice. If the delivery term puts import responsibility on a party that cannot hold the records, change the term before the deposit.
07The complaint that arrives in month three
Formaldehyde emission from a new panel is highest in the first weeks and falls as free formaldehyde migrates out. That decay is why a container that smells strong on opening can be unremarkable a month later, and why odour is not a measurement. Heat and humidity push the number the other way: a sealed container in summer, or a cabinet in a wet room, reads higher than the panel in a chamber.
The practical defence is a retained sample. Keep an offcut from each lot, wrapped and labelled with the purchase order line, the panel type and the date. If a complaint arrives, the sample and the label photograph are the only evidence tying the installed cabinet to a tested lot.
Panel freight has its own arithmetic. A 40HQ offers about 65 to 68 m³ of usable space and 26 to 28 tonnes of payload. At a declared density of 730 kg/m³ an 18 mm board weighs about 13.1 kg/m², so a full HQ of it would weigh around 47 tonnes: the container is weight-limited to roughly 1,980 m², some 36 m³, before payload is reached. A 20GP cubes out first: 28 m³ of the same board weighs about 20 tonnes against a payload near 28 tonnes. Heavy panels belong in the 20GP.
Decision rule: add a replacement clause tied to a chamber test on the retained sample, and state that the sample travels with the documents rather than in the container. A clause that says the supplier will consider complaints is not a remedy; one that names the test, the laboratory and the party who pays is.
What your RFQ should state
- The panel type and its limit: hardwood plywood 0.05 ppm, particleboard 0.09 ppm, MDF 0.11 ppm, thin MDF 0.13 ppm.
- The test method by name, ASTM E1333 or ASTM D6007, covering the quoted thickness and resin.
- The producing plant and the certifier, with the certificate number repeated on the proforma invoice.
- A labelled bundle for every lot, photographed at loading and filed against the purchase order line.
- The importer of record by name, and the delivery term that puts the certification duty on the party able to hold it.
- The ten-digit HTS code for the finished article and for any panel supplied separately, checked for Section 301 exposure.
- The ISPM 15 mark on crates, pallets and dunnage, kept separate from the panel compliance file.
- A retained offcut per lot, with the chamber test and the party bearing its cost named in the replacement clause.
Where this guidance stops
- This article covers the American federal and California regimes. Other destinations regulate wood products differently, and a European buyer needs EUDR due diligence in addition, not instead.
- The milligram conversions are approximate and depend on temperature and pressure. They are for orientation; the regulation's limits are in ppm under a named chamber method.
- A label and a report show that a lot was certified. They cannot show how the panels were stored after delivery, and heat, humidity and time change the emission a finished cabinet produces.
- We do not issue test reports, certify panels or act as importer of record. Foshan Supply coordinates sourcing, sampling, inspection and shipping documents; the supplier's certification and the agreed inspection scope govern.
- The container arithmetic uses a stated board density as an example. Replace it with the density on the supplier's data sheet before planning a load.
Questions buyers ask
Is CARB Phase 2 the same as TSCA Title VI?
The limits are the same, the jurisdictions are not. CARB Phase 2 is California's rule under Title 17 of the California Code of Regulations; TSCA Title VI is the federal rule at 40 CFR Part 770 and applies across the United States. The federal programme recognises California-approved certifiers, so one chamber report can serve both if it names the plant, thickness and resin.
Do kitchen cabinets need a CARB certificate?
The panels need certification, not the cabinet. A cabinet built from particleboard, hardwood plywood or MDF contains composite wood products, so the panel producer certifies and labels, and the fabricator who builds the cabinet keeps records for three years. Ask for the panel report and the bundle label rather than a cabinet certificate, which is not a document the rule creates.
Is E0 board compliant with CARB Phase 2?
It may be, but the E0 certificate does not prove it. E0 is an industry grade around 0.05 mg/m³ under the EN 717-1 chamber method, below all four American limits on paper. The method and the units differ, so the compliance decision still needs an ASTM E1333 or D6007 report for the panel being supplied.
What should be on a compliant panel label?
The producer's name, a lot or batch identifier, and a statement of compliance with TSCA Title VI. Panels made with no-added-formaldehyde or ultra-low-emitting-formaldehyde resins carry a different designation on the label. A label without a lot number cannot be tied to a test report, and a bundle without a label should not be loaded.
How long do the records have to be kept?
Three years for importers, fabricators, distributors and retailers under the federal rule. The record set includes the certification, the invoice and the lot identification that links a delivered cabinet to a tested panel. Keep the bundle label photographs in the same file, because they are what connects the paperwork to the goods.
Can a finished wardrobe be tested instead of the panels?
Finished-product testing exists, but the regulatory route runs through the panels and their records. Testing a whole wardrobe is slow and hard to repeat, and one result says little about a production run. A retained offcut from the same lot, tested in a chamber, is the practical evidence when a complaint arrives.
Does formaldehyde emission go away after a few weeks?
It falls, but not on a schedule you can rely on. Emission is highest when the panel is new and declines as free formaldehyde migrates out, while heat and humidity push it back up. A complaint in month three can be genuine, especially in a hot room or a wet area, which is why the retained sample matters more than the opening-day smell.
Sources
- Composite wood products programme — Airborne Toxic Control Measure, Phase 2 — California Air Resources Board
- Formaldehyde emission standards for composite wood products — TSCA Title VI — US Environmental Protection Agency
- Importing into the United States — entry and admissibility — US Customs and Border Protection
- Harmonized Tariff Schedule of the United States — US International Trade Commission
- ISPM 15 — Regulation of wood packaging material in international trade — International Plant Protection Convention
- Incoterms 2020 rules — International Chamber of Commerce
- Regulation on deforestation-free products (EUDR) — European Commission
- SOLAS — verified gross mass of packed containers — International Maritime Organization
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 8 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
