In short

A porcelain slab batch is a single firing run of a single body, sorted after firing for tone and for calibre, where calibre means the fired size class rather than the nominal format printed in the catalogue. The panel is pressed and fired mineral, not a resin composite: ISO 13006 and EN 14411 group BIa cap water absorption at 0.5%, and many slabs sit below 0.1%.

That distinction reaches the purchase order, because a quotation names a colour and a format, not a batch. Two panels that share a colour name, a 3,200 × 1,600 mm format and a 12 mm thickness can still read as two different surfaces along a single island run. The buyer tends to find out after the adhesive has cured.

01A batch is a firing run, not a colour name

A kiln does not deliver a perfectly uniform result, so a factory sorts slabs after firing and labels the crates by group. Two panels from one run can leave a little apart in colour and in size. That is why the labels exist, and why a colour name on a quote is not a batch code on a crate.

A quotation names the colour, because that is where the product is sold. The buyer inherits the risk: the sample looked right, the container looked right under showroom lights, and the second delivery did not.

02Tone and calibre drift for separate reasons

Tone is fired colour; calibre is fired size class. A factory sorts them independently, so a consignment can match the sample on colour and miss it on dimension.

Calibre matters wherever two panels meet: a worktop joint, a mitred edge, a book-matched pair either side of a sink. Two panels sold as 3,200 × 1,600 mm but sorted into different calibres give a joint that steps, or a gap that will not close without filler.

What can differ between two batches of the same nominal product, and how each difference appears on site
Variable What varies How it shows on site What to write in the order
ToneFired colour and shadeA change of colour at a joint, worst in daylightTone code recorded per slab
CalibreActual fired size classUneven joint width, a stepped edge, a gap that will not closeCalibre code, plus measured length and width on arrival
Vein registerWhere the pattern sits in the panelA book-matched pair that fails to mirrorPairs cut from consecutive slabs of one batch
FlatnessBow or twist after firingLippage at a joint; a thin panel that will not bed downFlatness checked on a straight edge before cutting
BodyColour beneath the surfaceA chip or a cut edge reading pale against the faceThrough-body or glazed, stated explicitly

These variables are sorted separately by the factory, so a consignment can pass on one and fail on another.

Catalogue reference: stone and slab catalogue — models, dimensions and finishes for the directions discussed above.

03A mixed batch shows up at the joint, not at the door

The common failure is not a slab in the wrong colour. It is the second slab. An L-shaped kitchen or a long island is fabricated from two panels: the first is cut and installed, the second arrives from a later run. Both carry the same colour name, and in mixed showroom light nobody sees a difference. On site, in daylight from a window at the end of the run, the joint reads as a line where the surface changes temperature.

By then the material is scrap. A cut slab cannot be returned as a colour mismatch, because the cut is the buyer's instruction, and the argument moves to whether the difference is within tolerance.

The arithmetic is worth doing before the order, because it decides how much material the batch question actually covers. A 3,200 × 1,600 mm slab is 5.12 m². A 2,600 × 1,200 mm slab is 3.12 m², so the larger format carries about 64% more area per panel. Take a kitchen with 9 m² of worktop and upstands, add 10% for cuts and edges, and the requirement is 9.9 m². Divided by 5.12 m², that is 1.93 slabs: two cover the area on paper, and three cover it once a veined direction and a retained offcut are allowed for. At 12 mm, one slab weighs 5.12 × 28 ≈ 143 kg, so three are about 430 kg before crating.

04How to check a consignment before it is cut

The check takes two people, a tape, a straight edge and daylight. Do it before the fabricator takes delivery, not after the first panel is on the bench.

  1. Unwrap two slabs from the same bundle and stand them on edge, faces clean and dry.
  2. Read the label on each slab and write down the batch, tone and calibre codes beside the packing list entry.
  3. Lay both face up, side by side, in daylight from a window, at the angle they will be seen at in the room.
  4. Put the signed control sample between them and compare all three at once, not one after another.
  5. Measure the actual length and width of each slab and record the difference in millimetres.
  6. Butt the two slabs together on a straight edge and photograph the joint with a tape in frame.
  7. Check every exposed corner for transit chips, which a later batch cannot repair.
  8. Send the photographs and the code list to the supplier for written confirmation before any cutting starts.

05The two offcuts and what each one proves

One offcut is not enough, because a colour dispute needs two pieces of evidence: what was approved and what was installed. Cut both from the delivered batch, before the panels are worked.

Offcut A is the control. It stays unsealed, goes into a sealed bag labelled with the batch, tone and calibre codes, the order number and the date, and is stored off site in the dark. It is the reference for any later delivery, and for a repair in year three.

Offcut B is the installed condition: same batch, finished and sealed exactly as the worktop is, kept on site and compared with the installed surface under the room's own light at handover. It answers what a photograph cannot, whether the surface changed after installation or was always that colour.

The two offcuts, where each is kept and what each can prove
Piece Where it is kept What it proves What it cannot do
Offcut A: batch controlOff site, sealed, dark, labelledWhat the factory shipped and what was approvedShow how the surface looks in the finished room
Offcut B: installed conditionOn site, finished and sealed as installedWhat the surface looks like under the room's lightProve the batch unless its label travels with it
Spare slab, same batchStore or site, uncutA repair panel that matches in a later yearHelp if the batch code does not match the installed work

Label every retained piece at the same time, with the same information. An offcut that cannot be tied to a batch is a tile, not evidence.

06What to hold back in the order and the contract

Hold back two things: material from the approved batch, and the right to refuse a substitute. Both are cheap at order stage and hard to buy later, because a factory is unlikely to reopen a firing run for one kitchen.

The quantity rule: one uncut panel for every continuous surface that could be damaged in service, plus the offcuts the cutting plan already produces. A spare is the reliable way to replace a panel that chips after handover, because a later run will not match and a repair from another batch reads as a patch at the joint.

Tie approval to the batch, not to the delivery date: no cutting until the codes are confirmed in writing.

07Thickness and support decide whether a batch difference is visible

A 6 mm panel is not a thinner version of a 20 mm worktop. It is a different construction: full substrate support, a bonded fixing, and a built-up or mitred edge to give the appearance of thickness. At 12 mm the panel can take a mitred edge and read as a solid top. At 20 mm it can be freestanding, at a weight that dictates the cabinet.

Porcelain runs at about 2.3–2.4 g/cm³, so 6 mm is roughly 14 kg/m², 12 mm roughly 28 kg/m² and 20 mm roughly 47 kg/m². A 5.12 m² panel at 20 mm is therefore about 241 kg, which is a lifting decision rather than a two-person job.

Thickness also changes how a batch problem presents. A thin panel bonded to a substrate cannot hide a bow: the adhesive pulls it down, the joint steps where calibres differ, and an unsupported edge lifts. A 20 mm panel resists the pull but loads the cabinet, so the substrate and batch questions arrive together.

Cutting is the last shared risk. Trimming a panel on site to close a calibre gap releases respirable crystalline silica, and OSHA 29 CFR 1926.1153 sets an eight-hour limit of 50 µg/m³ with engineering controls and wet cutting required. A batch that fits needs less site cutting, which is a safety argument as well as a cost one.

What your RFQ should state

  1. Product standard and class: ISO 13006 / EN 14411 group BIa, with the declared water absorption figure and its ASTM C373 result.
  2. Batch control: one batch per continuous surface, with batch, tone and calibre codes on the packing list for every crate.
  3. Control sample: one signed, dated offcut from the shipping batch, retained by the buyer before production begins.
  4. Pattern: whether the slab is through-body or glazed, and the vein direction marked on the cutting plan.
  5. Tolerances: the acceptable difference in actual length and width between slabs that will be joined, in millimetres.
  6. Spares: the number of uncut panels or offcuts held from the same batch, and who stores them.
  7. Substitution: written notice before any batch change, plus a replacement control sample and re-approval.
  8. Testing: the ASTM C648 breaking strength and C424 crazing reports that cover the supplied thickness, not the series.

Where this guidance stops

Questions buyers ask

What is a porcelain slab batch?

A batch is one firing run of one body. Because a kiln is not perfectly uniform, panels from the same run can differ slightly in colour and in fired size, so the factory sorts them into tone and calibre groups and labels the crates. The batch code is the most direct way to tie a delivered slab back to the run that made it.

What does calibre mean on a porcelain slab?

Calibre is the fired size class, not the nominal format. A slab sold as 3,200 × 1,600 mm is nominally that size, but firing shrinks and varies it slightly, so panels are sorted into calibre groups after the kiln. Two slabs of different calibre can be difficult to join with an even joint.

Can I mix two batches in one kitchen?

Only where the surfaces are physically separated and never seen together, such as a utility room and a main kitchen. On a continuous worktop or an island, a tone difference between two batches reads as a line at the joint in daylight. If you must mix, put the change at a full break with a different material or a cabinet, not mid-run.

How many spare offcuts should I keep?

Two, from the delivered batch, cut before fabrication: an unsealed control kept off site in the dark and labelled with the batch, tone and calibre codes, and a finished piece kept on site and sealed as the worktop is. Add an uncut spare panel if a surface could be damaged in service.

Will a reorder match my original slabs?

Probably not exactly. A later firing run is a different batch, and the body, the kiln and the sorting can all shift. Suppliers can sometimes hold stock from a run, but that depends on the volume and the time elapsed. Treat any match promise for a future order as something to confirm in writing with a batch code.

Is a tone difference a manufacturing defect?

Usually not by itself. Tone variation between batches is normal in a fired product; what matters is the tolerance written into the order rather than a promise of identical colour. It becomes a defect when the delivered slabs fall outside the tolerance agreed in the order, or when they do not match the signed control sample that both sides approved.

How do I check a delivery on site?

Unwrap two slabs from the same bundle, read the batch, tone and calibre labels, and lay them face up side by side in daylight with the signed control between them. Measure the actual length and width, butt the panels together on a straight edge, photograph the joint with a tape in frame, and send the set to the supplier before the fabricator cuts anything.

Sources

  1. ISO 13006:2018 — Ceramic tiles: definitions, classification, characteristics and marking — International Organization for Standardization
  2. ASTM C373 — Standard test methods for determination of water absorption and bulk specific gravity — ASTM International
  3. ASTM C648 — Standard test method for breaking strength of ceramic tile — ASTM International
  4. ASTM C1026 — Standard test method for measuring the resistance of ceramic tile to freeze-thaw cycling — ASTM International
  5. ASTM C424 — Standard test method for crazing resistance of fired glazed whitewares — ASTM International
  6. ANSI A326.3 — Test method for measuring dynamic coefficient of friction of hard surface flooring — Tile Council of North America
  7. Respirable crystalline silica — standards and resources — US Occupational Safety and Health Administration
  8. ANSI/ICPA SS-1 — Standard for quartz surfacing — International Cast Polymer Alliance

Pages related to this guide

How this guide was checked

FS

Foshan Supply editorial team · Catalogue indexMethodology

Written in Foshan and reviewed against the catalogue and public standards on 2026-11-05. This page is a buying guide, not a quotation or a warranty. How we work.

How to cite this page: Foshan Supply, “Porcelain slab batch consistency: what to hold back”, 2026-11-05, https://foshansupply.com/blog/porcelain-slab-batch-consistency/