In short
- Custom sofa construction is the specification of frame, suspension, foam and cover against a stated use and service life, not a choice between catalogue styles.
- Eight-way hand-tied coils suit deep, heavily used seats; sinuous springs, webbing and pocket coils each fail differently and carry different labour.
- Three numbers expose most weak quotes: foam density in kg/m³, Martindale cycles for the exact colourway, and covered metres per sofa.
Custom sofa construction is the specification of the parts a buyer never sees: the frame and its joints, the suspension, the foam and filling, the cover, and the order in which they are assembled. Those decisions are written against a stated use and a stated service life, then approved on a physical sample.
The cover is the only part most buyers compare, and it hides everything else. Two quotes can name the same fabric, width and delivery month and describe different products: one frame stapled at the back rail, the other mortised; one seat holding 1.7 kg of foam, the other 1.1 kg.
01The frame is a joint schedule, not a species name
A hardwood name says little until the joints, the moisture content and the corner blocks are named. Beech, ash and rubberwood all appear as 'solid hardwood', and all can be assembled badly. A stapled softwood frame with a glued corner block outlasts a hardwood frame whose back rail is held by two staples, because that rail takes the load when someone pushes on the back to stand up.
Ask how each loaded joint is made, not what the frame is made of. Mortise-and-tenon and double dowel with glue hold under reversing load; corner blocks stiffen the seat rail. Check square by comparing both diagonals of the seat box, because a frame out of square shows at the arms and then at the seams, after the cover is cut.
Timber is a moisture problem before it is a strength problem. Wood machined wet keeps shrinking after assembly and opens the joint it was glued into. Ask for the moisture content measured at machining to EN 13183-1 and write the figure you accept into the order.
Decision rule: reject a frame stapled at the back rail and arm joints, whatever the species list says, and reject one whose moisture figure is not declared at all.
Clause: 'Frame in kiln-dried hardwood or hardwood plywood; moisture measured at machining to EN 13183-1; all load-bearing joints glued and mortised or dowelled; corner blocks glued and screwed; frame square within the stated tolerance.'
02Four suspensions, four different failures
Eight-way hand-tied suits a deep seat. It is not the only answer, and it is not automatically right inside a slim frame. Suspension is a load path: the rail carries the springs, the springs carry the cushion, and each system gives way at a different point.
| System | Load path | Suits | Failure | Repair |
|---|---|---|---|---|
| Sinuous spring | Zig-zag springs clipped to front and back rails, with a cross-wire | Shallow and mid-depth frames | Clip wear; sag between springs | Clips or one spring, from below |
| Eight-way hand-tied | Coils lashed in eight directions to jute twine on webbing | Deep, heavily used seats | Twine stretch; weak knots | Re-tie or replace coils |
| Elastic webbing | Elastomer straps stretched across the rails | Slim, low-profile frames | Relaxation and perishing; centre sag | Re-web the deck |
| Pocket coil unit | Coils in fabric pockets, clipped as one unit | Wide seats, two comfort zones | Migration if unclipped; coil noise | Unit, if the dust cover opens |
| Foam platform | Dense foam slab on a plywood deck | Low-profile and modular sofas | Compression set at the front edge | Replace the slab |
The repair route belongs in the specification: a deck that cannot be opened turns a repair into a rebuild.
Read the table as repair decisions. A hand-tied seat can be re-tied; a pocket coil unit is replaceable only if the underside opens; a foam platform is simplest to remake and least forgiving.
Match the system to build depth and use. A seat deeper than about 600 mm, used for long evenings, spreads load better across coils or tied springs. A frame with roughly 120 mm of internal depth cannot take a coil unit, and webbing may be the honest construction. Decision rule: choose from seat depth, daily hours and the repair route you want in five years, then ask for wire gauge, spring count and cross-wire.
Clause: 'Suspension: [system], spring count and wire gauge declared, cross-wire fitted, dust cover removable for inspection.'
Catalogue reference: furniture and fitted living — models, dimensions and finishes for the directions discussed above.
03Density is the number, hardness is the feel
Seat foam is bought by density and felt by hardness, and the two are different figures. Density is mass per cubic metre. Contract seating is commonly specified at 35–45 kg/m³, and a pad below that range collapses at the front edge.
The arithmetic is small and revealing. A pad 600 × 600 × 120 mm is 0.0432 m³: about 1.7 kg of foam at 40 kg/m³, about 1.1 kg at 25 kg/m³. The showroom seat feels the same, because a low-density pad can be made firm for a month. The difference arrives as a crushed front edge in year two.
Hardness is the figure the buyer actually approved. A firm pad can be low-density; a soft pad can be dense and last. Specify hardness separately so the approved feel is not what a factory trades when a grade runs out. Decision rule: set a seat minimum and a separate figure for back and arms, both printed on the sample label.
Clause: 'Seat foam minimum 35 kg/m³; back and arm densities declared separately; hardness at 25% compression with the method named; density printed on the sample label.'
04The cushion build decides who plumps it
The cushion is what the sitter feels first and what housekeeping lives with afterwards.
| Build | Construction | Feel | Upkeep | Suits |
|---|---|---|---|---|
| Wrapped foam | Foam core bonded to a fibre wrap | Firm with a soft surface | Brush and rotate; wrap mats | Hotels, rental flats, family use |
| Pocket-coil cushion | Coil unit inside foam, wrapped | Springy, even, slower to settle | Rotate; unit cannot be re-tied | Wide seats shared by two |
| Fibre-wrapped foam | Foam core in a loose fibre jacket | Softer crown, settles visibly | Plump weekly | Living rooms, light traffic |
| Feather and down | Core in a down-proof jacket | Loose, nest-like | Plump daily | High-end residential |
| Fibre-only back | Loose or bagged fibre | Soft, light | Plump and refill | Back cushions |
A back cushion 550 mm high that is never plumped will lose its crown. No factory prevents that; the instruction belongs in the specification.
Removable covers change the maintenance question. A zip and a care code let a hotel swap a stained panel instead of writing off a seat; a fixed cover makes the sofa one unit for its life.
Decision rule: where the people maintaining the room have minutes rather than hours, specify wrapped foam with removable covers, and keep feather wraps for rooms where someone will plump them daily.
Clause: 'Cushion build [build] with core density, wrap weight in g/m² and finished dimensions; fixed or removable covers with zip; care code stated; one spare cover per seat position quoted separately.'
05The cover is lost at the cutter, not in the showroom
Fabric is the line most often under-ordered, because it is quoted in metres and lost at the cutting table. Yield depends on usable roll width, repeat in both directions, and railroading.
Take a cushion face 700 × 700 mm. On 1,400 mm usable width, two faces sit side by side, so three cuts give six faces in 2.1 m. With a 350 mm repeat that must match at the seam, each cut rounds to 1,050 mm: 3.15 m, or 1.05 m more on the seat faces alone, before boxing and welt.
Abrasion is reported for the colourway tested. 30,000–40,000 Martindale cycles to ISO 12947 is the customary contract floor; the United States uses Wyzenbeek double rubs to ASTM D4157, and the two units do not convert. Fire evidence belongs to the destination: California TB 117-2013 tests components for smoulder resistance, BS 5852 tests named ignition sources, and the IMO FTP Code applies on ships.
Decision rule: ask for metres per sofa from the cutter's marker, not a percentage allowance, and approve the marker before the roll is cut. On customer's own material (COM), agree who carries a shortfall, who inspects the roll and which report covers the colourway.
Clause: 'COM: usable width and repeat both directions; railroading permitted or not; yield per sofa on the approved marker; shortfall and dye-lot responsibility stated.'
06A signed sample is the only approval that travels
A drawing carries dimensions; a sample carries the decisions the line will copy. The gap is where custom sofas go wrong, because the bench reproduces what is in front of it.
Photograph the sample under the lighting of the room it will sit in, not the factory's, since grey and beige change character at a window. Record on the label: overall width, depth and height; seat height and depth; arm profile; seam type at seat front and inside arm; welt or none; leg finish and glide; foam density; suspension; fabric roll and dye lot.
Measure the first article against the drawing with a tolerance you set, for example ±10 mm on overall width, and sit on every seat position before signing. A squeak now is a clip or a dry joint; the same squeak after delivery is a service call in a finished room.
Decision rule: no production release until the sample carries a dated label with foam density, suspension and roll number, signed by whoever will accept delivery.
Clause: 'Approved sample retained by both parties; production matched to the sample label; any substitution of foam, suspension or fabric re-submitted for written approval before shipment.'
07Open the crate before the sofa enters the building
The crate is the last moment when a defect can be attributed to transit rather than site handling. Once the packing is broken down, that argument is lost.
- Photograph the crate and the packing before anything is lifted.
- Measure width, depth, height, seat height and seat depth against the sample sheet.
- Measure each cushion at the centre and front edge, and date the figures.
- Sit on every seat position for a minute and listen for a squeak or click.
- Compare the seat-front and inside-arm seams and the pattern match with the sample.
- Check legs, glides, dust cover and every zip, and confirm the care code.
- Re-measure the cushions after 30 days in the room.
The 30-day re-measure makes a later sagging complaint arguable. Without a delivery figure, a supplier can say the cushion was always that height.
Decision rule: raise defects with photographs and measurements inside the inspection window, before the packing is discarded. Clause: 'Inspection on arrival with photographs; cushion measurements at delivery and at 30 days; spare covers and one leg set as separate lines.'
What your RFQ should state
- Frame species, moisture content measured at machining to EN 13183-1, and the figure you will accept.
- Every load-bearing joint named, with glue, dowel or mortise stated, and corner blocks glued and screwed.
- Suspension named, with spring count, wire gauge and whether a cross-wire is fitted.
- Seat, back and arm foam densities in kg/m³, each with hardness at 25% compression and the method.
- Cushion build, core density, wrap weight in g/m², fixed or removable covers, and the care code.
- COM yield per sofa from an approved cutter's marker, with shortfall and dye-lot responsibility.
- Abrasion and fire evidence for the exact colourway and destination market, as named standards.
- A dated approval-sample label, the dimensional tolerance, and the inspection window after arrival.
Where this guidance stops
- This article describes construction, not a product or a price. Two sofas built to the same clause can still differ in comfort and in how carefully the frame was jigged.
- The photograph above shows a cover and a proportion. It cannot show foam density, joint type, spring count or wrap weight; the sample label and data sheet carry those.
- Density, hardness and fill weights are supplier declarations unless a report is bought. Nothing here substitutes for a laboratory report or a factory audit.
- Fire and accessibility requirements are set by the destination's building code. A standard named here is a question for the supplier, not an approval for a project.
- Foshan Supply coordinates sourcing, sampling and inspection. We do not manufacture, issue test reports, install furniture or offer a universal warranty; the agreed scope governs.
Questions buyers ask
Is eight-way hand-tied suspension worth specifying?
It is worth it when the seat is deep, the users are heavy and the sofa is the main seat in the room, because load spreads across many tied coils and the deck can be re-tied later. It is not worth it in a slim frame with around 120 mm of build depth, where webbing or a foam platform is the honest construction.
What foam density should a sofa seat have?
35–45 kg/m³ is the range contract seating is commonly specified at, and a pad below it crushes at the front edge first. Ask for seat, back and arm figures separately, and for hardness at 25% compression with the method named. Density is not hardness: a firm pad can be low-density and feel adequate for a month.
Can I compare Martindale cycles with Wyzenbeek double rubs?
No, there is no conversion factor. Martindale (ISO 12947) rubs in a figure of eight and reports cycles; Wyzenbeek (ASTM D4157) rubs back and forth and reports double rubs. 30,000–40,000 Martindale cycles is the customary contract floor, and the report must cover the colourway you are buying.
Can I supply my own fabric for a custom sofa?
Yes, as COM, with conditions. The supplier should confirm usable width, repeat in both directions, whether railroading is allowed, and metres per sofa from a cutter's marker. Agree in writing who carries a shortfall, who inspects the roll, and which report covers the colourway. Fire performance remains the destination's requirement.
How long should a custom sofa last?
That depends on which part fails first, so a single figure misleads. In contract use the foam and cover usually go before the frame; in a lightly used living room the frame joint and a webbing deck are the weak points. Specify the repair route for each part at order.
Do I need a mock-up room for a single sofa?
A mock-up room is a hotel process; for one sofa the equivalent is a production sample approved before the cover is cut. It should carry a label with foam density, suspension, seam type and fabric roll number, signed and dated by whoever will accept delivery. Photographs in the room's lighting plus that label are enough.
Can a custom sofa be repaired or reupholstered later?
Usually, if the frame is screwed or bolted rather than stapled and the covers are removable. A hand-tied deck can be re-tied, webbing re-stretched and sinuous clips replaced; a pocket coil unit needs the dust cover to open. Ask for that cover to be fixed with staples or hook-and-loop.
Sources
- BIFMA standards — seating (X5.1), desks (X5.5) and storage (X5.9) — BIFMA
- Technical Bulletin 117-2013 — flammability of upholstered furniture components — California Department of Consumer Affairs, Bureau of Household Goods and Services
- ISO 12947 — abrasion resistance of fabrics by the Martindale method — BSI
- 2010 ADA Standards for Accessible Design — clear floor space, routes and reach ranges — US Department of Justice
- ASTM D4157 — abrasion resistance of textile fabrics (oscillatory cylinder method) — ASTM International
- BS 5852 — ignitability of upholstered seating by smouldering and flaming ignition sources — BSI
- IMO FTP Code — international code for application of fire test procedures — International Maritime Organization
Pages related to this guide
How this guide was checked
- Written from the public catalogue, the standards and regulator pages listed under Sources, and the process records described on the services page.
- Catalogue references and model details were checked on 2026-11-05; 7 primary sources are linked above.
- No supplier paid for placement. No price on this page is an offer; ranges are planning references and must be confirmed in a quotation.
How these guides are researched and reviewed · Corrections policy
